Dell Inspiron N4030 Service Manual - Page 13

Processor Module

Get Dell Inspiron N4030 PDF manuals and user guides View all Dell Inspiron N4030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Back to Contents Page Processor Module Dell™ Inspiron™ N4020/N4030 Service Manual Removing the Processor Module Replacing the Processor Module WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on your computer). CAUTION: To prevent intermittent contact between the ZIF-socket cam screw and the processor module when removing or replacing the processor, press to apply slight pressure to the center of the processor module while turning the cam screw. CAUTION: To avoid damage to the processor module, hold the screwdriver so that it is perpendicular to the processor module when turning the cam screw. CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the computer. Removing the Processor Module 1. Follow the instructions in Before You Begin. 2. Remove the thermal cooling assembly (see Removing the Thermal Cooling Assembly). 3. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop. 1 ZIF socket 2 ZIF-socket cam screw CAUTION: To ensure maximum cooling for the processor module, do not touch the heat transfer areas on the processor thermal-cooling assembly. The oils in your skin can reduce the heat transfer capability of the thermal pads. CAUTION: When removing the processor module, lift the module straight up. Be careful not to bend the pins on the processor module. 4. Lift the processor module from the ZIF socket. Replacing the Processor Module

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Back to Contents Page
Processor Module
Dell™ Inspiron™ N4020/N4030 Service Manual
Removing the Processor Module
Replacing the Processor Module
Removing the Processor Module
1.
Follow the instructions in
Before You Begin
.
2.
Remove the thermal cooling assembly (see
Removing the Thermal Cooling Assembly
).
3.
To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.
4.
Lift the processor module from the ZIF socket.
Replacing the Processor Module
WARNING:
Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION:
Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™
is not covered by your warranty.
CAUTION:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION:
To prevent intermittent contact between the ZIF-socket cam screw and the processor module when removing or replacing the
processor, press to apply slight pressure to the center of the processor module while turning the cam screw.
CAUTION:
To avoid damage to the processor module, hold the screwdriver so that it is perpendicular to the processor module when turning the
cam screw.
CAUTION:
To help prevent damage to the system board, remove the main battery (see
Removing the Battery
) before working inside the
computer.
1
ZIF socket
2
ZIF-socket cam screw
CAUTION:
To ensure maximum cooling for the processor module, do not touch the heat transfer areas on the processor thermal-cooling assembly.
The oils in your skin can reduce the heat transfer capability of the thermal pads.
CAUTION:
When removing the processor module, lift the module straight up. Be careful not to bend the pins on the processor module.