Dell PowerConnect 8100 Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi
Dell PowerConnect 8100 Manual
 |
View all Dell PowerConnect 8100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerConnect 8100 manual content summary:
- Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 1
Deploying Dell PowerConnect 8100 and Cisco Catalyst Switches Using the Dell PowerConnect 8100 Series switch with the Cisco Catalyst WS-C6504-E Andrew Berry Victor Teeter Kevin Locklear - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 2
the Dell PowerConnect 8100 with the Cisco Catalyst This document is for informational purposes only and may contain typographical errors and technical inaccuracies. The content is provided as is, without express or implied warranties of any kind. © 2012 Dell Inc. All rights reserved. Dell and - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 3
Cisco Catalyst 6500 5 Dell PowerConnect 8100 CLI 6 Cisco Catalyst CLI ...7 Access, trunk and general Switchport Modes 8 VLAN configuration example 9 Dell PowerConnect 8100 CLI 9 Cisco Catalyst CLI 10 PVID and native VLAN 11 Dell PowerConnect 8100 CLI 11 Cisco Catalyst CLI 12 Creating and - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 4
/core platforms interoperate or replace the Cisco Catalyst switches. This document providesquick reference guidance in key areas for configuring or integrating the Dell PowerConnect 8100 series switches with the Cisco Catalyst 6500 series. The most critical aspects and differences with deploying - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 5
for easier management, better security, and improved administration. Creating and assigning VLANs Creating VLANs on the Dell PowerConnect 8100 is simple and exactly the same on the Cisco Catalyst WS-C6504-E. Both switches have the VLAN xx command available to manually create a VLAN and both create - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 6
not for user traffic, just like the management VLAN on the Dell switch. Figure 5 shows the basic topology of a management VLAN that is configured in this example: creating and then connecting a management VLAN and an SVI. Management VLAN across a Dell PowerConnect 8100 Figure 5. Both switches use - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 7
the Dell PowerConnect 8100 switch to create a management VLAN, which allows in-band management to the switch. console#configure CLI Run the commands below on the Cisco Catalyst switch to create an SVI, which allows in-band management to the switch. cat6504E_1#configure terminal Enter configuration - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 8
are essentially the same for both switches and are found in the Dell PowerConnect 8100 User Configuration Guide. Access, trunk and general Switchport Modes The Dell PowerConnect 8100 series switches can have each port configured in one of the following modes (Dell.com, 2012): Access Access ports - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 9
is an example of a much abbreviated network configuration between two (2) end-user systems, the campus switch, and the core. Example of access, and trunk VLANs Figure 6. Dell PowerConnect 8100 CLI Run the commands below on the Dell PowerConnect 8100 switch to create an access mode switchport going - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 10
Deploying the Dell PowerConnect 8100 with the Cisco Catalyst console(config)# interface range te1/0/47- no shut console(config-if-Po1)#exit Cisco Catalyst CLI Here are the commands to run on the Cisco Catalyst 6504: Cat6504E_1#configure terminal Cat6504E_1(config)#vlan 100,101 Cat6504E_1(config-vlan - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 11
the PVID specified for the port that received the frame (Dell.com, 2012). Dell PowerConnect 8100 CLI Run the commands below to configure Dell PowerConnect 8100 series switch for an untagged VLAN on port 1. console#configure console(config)#vlan 100 console(config-vlan)#exit console(config)#interface - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 12
Run the commands below to configure the Dell PowerConnect 8100 series switch for a general mode tagged VLAN on port 10, egressing to another switch. The PVID setting is console(config-if-Te1/0/10)#exit Cisco Catalyst CLI Run the commands below to configure an access port on a single interface of - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 13
malfunctioning. An example of CLI necessary to create and assign port-channels (LAGs) is found on page 9 and 10. The only note to remember is that the Cisco switches support a proprietary form of LAGs with the PaGP feature that the Dell PowerConnect switch does not support. Enabling Spanning Tree - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 14
protocols (STP, RSTP) on the Dell PowerConnect switches, additional instruction on the network is required. Below are two common methods to get the job done. Method 1: Portfast Ports on the Cisco Catalyst switch that are directly connected to the Dell PowerConnect 8100 can be forced into forwarding - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 15
to the Dell PowerConnect 8100s. cat6504E_1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. cat6504E_1(config)#interface tengigabitethernet 2/5 cat6504E_1(config-if)#spanning-tree portfast network Review the bridge priority configurations on each switch to make - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 16
the User Guides for your devices on how to set up MST. Cisco proprietary protocols Network administrators often run into problems receiving multiple Cisco proprietary protocols on standards based switches, which causes unexpected results on the network. Therefore, Dell PowerConnect has developed - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 17
the Dell PowerConnect 8100 with the Cisco Catalyst interface option enforces the dropping of CDP packets for the ingress on this interface even if the global setting is enabled). For more information, see the Link Local Protocol Filtering section in the PowerConnect 8100 User's Configuration Guide - Dell PowerConnect 8100 | Deploying Dell PowerConnect 8100 and Cisco Catalyst Swi - Page 18
versions Version information for the network switches used in creating this document are as follows: Network switch Dell PowerConnect 8100 Cisco Catalyst WS-C6504-E Software Version 5.0.0.4 IOS 12.2(33)SXI4a; About Dell Dell (NASDAQ: DELL) is a leading technology provider to commercial and public
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
Andrew Berry
Victor Teeter
Kevin Locklear
Using the Dell PowerConnect 8100 Series switch with the Cisco Catalyst
WS-C6504-E
Deploying Dell PowerConnect 8100
and Cisco Catalyst Switches