Dell PowerConnect J-8216 Release Notes JUNOS version 10.3

Dell PowerConnect J-8216 Manual

Get Dell PowerConnect J-8216 PDF manuals and user guides View all Dell PowerConnect J-8216 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell PowerConnect J-8216 manual content summary:

  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 1
    EX Series Ethernet Switches. They describe device documentation and known problems with the software. You can also find these release notes at http://www.support.dell.com/manuals. Junos OS Release Notes for Dell PowerConnect J-SRX Series Services Gateways 4 New Features in Junos OS Release 10.3 for
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 2
    in Junos OS Release 10.3 for J-SRX Series Services Gateways 24 AppSecure 24 Chassis Cluster 24 Command-Line Interface (CLI 25 Dynamic VPN 25 Flow and Processing 26 Interfaces and Routing 26 IPv6 Support 26 J-Web Browser Support 26 NetScreen-Remote 28 Network Address Translation (NAT 28
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 3
    Instructions for Junos OS Release 10.3 for J-SRX Series Services Gateways 52 Junos OS Release Notes for Dell PowerConnect and Spanning Trees 54 Class of Service 54 Firewall Filters 55 Hardware 55 Infrastructure 55 Interfaces 56 J-Web Browser Support 56 Layer 2 and Layer 3 Protocols
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 4
    OS, Dell PowerConnect J-SRX Series Services Gateways provide robust networking and security services. J-SRX Series Services Gateways range from lower-end devices designed to secure small distributed enterprise locations to high-end devices designed to secure enterprise infrastructure, data centers
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 5
    problem can sometimes be difficult to identify. The show security match-policies command allows you to troubleshoot traffic problems the cost of communication. To support this feature, a new Secure Router User Guide] Group VPN Interoperability environment that includes both Dell security devices and
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 6
    a method for adding and removing group members, is not supported with group VPN on Dell security devices. GET VPN members can be configured for cooperative and Syntax in Junos OS Release 10.3 for J-SRX Series Services Gateways The following current system behavior, configuration statement usage, and
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 7
    to change the order number of the custom signature if it conflicts with another application signature. • The output of the show services application-identification application-system-cache command has been changed. The new output includes the cache statuses and the timeout value for maintaining
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 8
    LAN (VLAN) tag used for control-link traffic will be replaced with the use of experimental Ether type 0x88b5. However, backward compatibility is also supported for devices that have already deployed chassis cluster with VLAN tagging in place. • To toggle between VLAN and Ether type modes, use the
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 9
    Changes in Default Behavior and Syntax in Junos OS Release 10.3 for J-SRX Series Services Gateways Command-Line Interface (CLI) • On AX411 Access Points, the possible completions available for the CLI command set wlan access-point < ap_name > radio < radio_num > radio-
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 10
    Junos 10.3 OS Release Notes 13 Channel 13 14 Channel 14 auto Automatically selected • On AX411 Access Points, the possible completions available for the CLI command set wlan access-point mav0 radio 1 radio-options mode? have changed from previous implementations. Now this CLI command displays the
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 11
    Changes in Default Behavior and Syntax in Junos OS Release 10.3 for J-SRX Series Services Gateways • On J-SRX Series devices, the show system storage partitions command now displays the partitioning scheme details on J-SRX Series devices. • Example 1: show system storage
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 12
    of aggregated interfaces. set chassis aggregated-devices ethernet device-count xxx Support to add multiple links from each chassis to a reth interface default configuration is inconsistent with the one in Secure Services Gateways, thus causing problems when users migrate to J-SRX Series devices. As
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 13
    on the HOST. • On J-SRX100, J-SRX210 and J-SRX240 devices, support for USB auto-installation is added. This feature simplifies the upgrading of new configuration attribute management-url is introduced at the [edit system services web-management] hierarchy level to control J-Web access when both J-
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 14
    VPN must have the configured HTTPS certificate and the webserver to communicate with the client. Therefore, the configuration at the [edit system services web-management] hierarchy level required to start the appweb webserver cannot be deleted or deactivated. To disable J-Web, the administrator must
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 15
    Changes in Default Behavior and Syntax in Junos OS Release 10.3 for J-SRX Series Services Gateways J-Web is not enabled, and dynamic VPN is not configured. Navigates to the Page Navigates to the Page Not Found page Not Found page
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 16
    less latency for LFI traffic and to avoid out of order transmission of data traffic: Configure the following schedulers • set class-of-service schedulers S0 buffer-size temporal 20K • set class-of-service schedulers S0 priority low • set class-of-service schedulers S2 priority high • set class-of
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 17
    of Access Points . You might have to power cycle the Access Points manually to avoid this issue. • The J-SRX Series devices that are not the SSH access using the set wlan access-point < name > external system services enable-ssh command. VLAN • Native-vlan-id can be configured only when either
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 18
    message. set chassis craft-lockout set chassis routing-engine on-disk-failure Class-of-Service Hierarchy • On J-SRX100, J-SRX210, and J-SRX240 devices, the following class-of-service hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 19
    CLI on page 21 • T1 Interface CLI on page 22 • VLAN Interface CLI on page 22 Aggregated Interface CLI • The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message. request lacp link-switchover
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 20
    0 radio-router set interfaces at-1/0/0 unit 0 transmit-weight set interfaces at-1/0/0 unit 0 trunk-bandwidth Ethernet Interfaces • The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message. set
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 21
    error message. set interfaces gr-0/0/0 unit 0 ppp-options set interfaces gr-0/0/0 unit 0 layer2-policer IP Interface CLI • The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message. set interfaces
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 22
    inet dhcp set interfaces t1-1/0/0 unit 0 inverse-arp set interfaces t1-1/0/0 unit 0 multicast-dlci VLAN Interface CLI • The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message. set interfaces
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 23
    set routing-instances p1 protocols amt set routing-options bmp set routing-options flow Services Hierarchy • On J-SRX100, J-SRX210, and J-SRX240 devices, the following services hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 24
    devices have the following chassis cluster limitations: • Virtual Router Redundancy Protocol (VRRP) is not supported. • In service software upgrade (ISSU) is not supported. • The 3G dialer interface is not supported. • On J-SRX Series device failover, access points on the Layer 2 switch reboot and
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 25
    and port mirror on the reth interface are not supported. • Switching is not supported in chassis cluster mode. • The Chassis Cluster MIB is not supported. • Any packet-based services like MPLS and CLNS are not supported. • lsq-0/0/0-Link services Multilink Point-to-Point Protocol (MLPPP), Multilink
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 26
    Configuration Guide. J-Web Browser Support • J-Web Browser Support for Your Dell PowerConnect J-Series Devices-To access the J-Web interface for all platforms, your management device requires the following Windows operating system and browsers: • Operating System: Microsoft Windows XP Service Pack
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 27
    Release 10.3 for J-SRX Series Services Gateways NOTE: Other browser versions may work but are not supported. NOTE: Only English-version browsers are supported. NOTE: For both J-SRX and J-EX devices, the browser and the network must support receiving and processing HTTP 1.1 GZIP compressed data. 27
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 28
    supported in Junos OS Release 10.3. Network Address Translation (NAT) • NAT rule capacity change-To support wide limitation on how many rules a device can support. This restriction is provided to help you better plan SRX210, and J-SRX240 devices, CoA is not supported with 802.1x. • On J-SRX100, J-
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 29
    The number of licensed access points can exceed the maximum number of supported access points. However, you can only configure and manage the maximum 10.3 for J-SRX Series Services Gateways on page 4 Documentation • Issues in Junos OS Release 10.3 for J-SRX Series Services Gateways on page 29 •
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 30
    Junos 10.3 OS Release Notes Outstanding Issues In Junos OS Release 10.3 for J-SRX Series Services Gateways The following problems currently exist in J-SRX Series devices. The identifier following the description is the tracking number in our bug database. Application Layer Gateways (ALGs) • On J-
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 31
    Issues in Junos OS Release 10.3 for J-SRX Series Services Gateways • Back-to-back redundancy group 0 failover • appropriately set to prevent the file system from getting full. [PR/454926] • During a manual failover, a system crash might occur if the nodes have not completely recovered from a
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 32
    of Service (CoS) • On J-SRX Series devices, class-of-service-based During this process, the UDP data port on the TFTP server might In this case, you should manually fetch the file from the down for long duration traffic when FPGA 2.3 version is loaded in the device. As a result, the multilink goes
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 33
    for J-SRX Series Services Gateways • On J-SRX might be seen after more than 24 hours of continuous high load. Forwarding restarts when the forwarding core file is generated; then is set to forced speed, the behavior is indeterminate and not supported. [PR/423632] • On J-SRX Series devices, the RPM
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 34
    bring up the logical interface. [PR/472198] • On J-SRX210 devices with VDLS2, ATM COS VBR related functionality cannot be tested because of lack of support from the vendor. [PR/474297] • On J-SRX210 High Memory devices, IGMP v2 JOINS messages are dropped on an IRB interface. As a workaround, enable
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 35
    Issues in Junos OS Release 10.3 for J-SRX Series Services Gateways As a workaround, configure radius-server outside the profile option under access option. [PR/503717] • On J-SRX100, J-SRX210, and J-SRX240 devices, egress queues are not supported on VLAN or IRB interfaces.[PR/510568] • On J-SRX240
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 36
    the results, navigate to page 1 manually. [PR/476338] • On J-SRX210 devices, in the J-Web interface, there is no support to change the T1 to E1 interface and vise on Firefox 3.0, the resource utilization does not load any data in the dashboard page. [PR/564165 ] the services gateway fails to boot with the
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 37
    Issues in Junos OS Release 10.3 for J-SRX Series Services Gateways ports to a maximum power of 12.4 watts. Use the following command to configure the ports: root#set poe interface all maximum-power 12.4 [PR/
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 38
    • Low-impact ISSU chassis cluster upgrades are not supported in Junos OS Release 10.3. ISSU upgrade to 10.3 might cause loss of configuration. In order to upgrade to 10.3, use the normal upgrade procedure described in the Junos OS Installation and Upgrade Guide . [PR/526599 and PR/526829] USB Modem
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 39
    Link Layer Discovery Protocol (LLDP) Protocol Data Units (PDUs) from neighbors. [PR/ (for example, laptop or computers) are not supported. The first user session will get disconnected when Junos OS Release 10.3 for J-SRX Series Services Gateways. The identifier following the descriptions is the
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 40
    been resolved.] • On J-SRX210 devices, packet drop was seen while prioritizing multiple data streams configured with same multilink class on single-member link ML bundles that were devices, MAC address changes for VLAN interface were not supported. [PR/518934: This issue has been resolved.] 40
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 41
    (for example, protocol name, filename, and description), then you could not delete the data with double quotation marks through J-Web. [PR/464030: This issue has been resolved.] -attack-groups changes that included Solaris Services - All attack group. [PR/546705: This issue has been resolved.] 41
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 42
    10.3 for J-SRX Series Services Gateways Changes to the Junos Documentation Set This section lists changes in the documentation. Single Commit on J-Web The following information pertains to J-SRX Series devices: • For all J-Web procedures, follow these instructions to commit a configuration: • If
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 43
    Help instructions were available both in the Help and in the administration and configuration guides. These topics have been removed from the guides and J-SRX100, J-SRX210, and J-SRX240 support the Application Layer Gateways (ALGs) feature. • The Feature Support Reference for SRX Series and J Series
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 44
    , use the provided CLI instructions. Security Configuration Guide • ALG configuration examples in the Junos OS Security Configuration Guide incorrectly show policy-based NAT configurations. NAT configurations are now rule-based. • The "Verifying the Policy Compilation and Load Status" section of the
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 45
    the SA, ". . . terminates after 1800 KB of data pass through it." It should instead say, ". . . after 1800 seconds." • In the "Example: Accommodating End-to-End TCP Communication for J Series Services Routers" section of the Junos OS Security Configuration Guide, one CLI command given in the example
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 46
    • J-SRX100 Services Gateway Quick Start Guide • J-SRX210 Services Gateway Quick Start Guide • J-SRX240 Services Gateway Quick Start Guide The correct server, you can manually configure it with the J-Web interface. The correct information for this section is as follows: The services gateway acts as a
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 47
    server, you can manually configure it with the J-Web interface. The correct information for this section is as follows: The services gateway acts as a server. • Installing Software Packages-The current J-SRX210 Services Gateway Hardware Guide does not include the following information: On J-SRX210
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 48
    DHCP server, you can manually configure it with the J-Web interface. The correct information for this section is as follows: The services gateway acts as a J-SRX240 Services Gateway Hardware Guide is missing information about the following statements and data: • The "J-SRX240 Services Gateway Site
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 49
    be treated as an Isolated DC return (DC-I), as defined in GR-1089-CORE. • The "J-SRX240 Services Gateway Installation Instructions Warning' section in Appendix J-SRX240 Services Gateway Installation Safety Guidelines and Warnings should specify the following statements: • Before you make any crimp
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 50
    supported. The guide should state that only the DOCSIS 3.0 U.S. model of the DOCSIS Mini-PIM is supported. Related Documentation • New Features in Junos OS Release 10.3 for J-SRX Series Services OS. Please contact Dell for the correct transceiver and supports data transfer across the network
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 51
    Independent Call Control (BICC) • Direct Data Placement Segment chunk (DDP-segment) • Direct Data Placement Stream session control (DDP-stream) firewall supports deeper inspection: • Packet filtering-The profile configuration of drop packets for special SCTP payload protocol and M3UA service enables
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 52
    traffic. Upgrade and Downgrade Instructions for Junos OS Release 10.3 for J-SRX Series Services Gateways In order to upgrade support, see the software overview information in the Dell PowerConnect J-EX Series Ethernet Switch Complete Software Guide for Junos OS at http://www.support.dell.com/manuals
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 53
    used to secure OSPFv3 interfaces and protect OSPFv3 virtual links by authenticating and encrypting each IP packet of a data stream. • IGMP snooping EXCLUDE modes-IGMP snooping now supports IGMPv3 EXCLUDE and EXCLUDE NULL modes. • Layer 2 protocol tunneling-L2PT on J-EX Series Ethernet switches now
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 54
    more than 64,000 MAC address clone routes in a single VLAN causes the Routing Engine to create core files and reboot. Class of Service • On J-EX8200 switches, classification of packets using ingress firewall filter rules with forwarding-class and loss-priority configurations does not rewrite the
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 55
    than 128 bytes. • On J-EX Series Ethernet switches, the show snmp mib walk etherMIB command does not display any output, even though the etherMIB is supported. This occurs because the values are not populated at the module level-they are populated at the table level only. You can issue show snmp
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 56
    output. J-Web Browser Support • J-Web Browser Support for Your Dell PowerConnect J-Series Devices-To access the J-Web interface for all platforms, your management device requires the following Windows operating system and browsers: • Operating System: Microsoft Windows XP Service Pack 3 • Browser
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 57
    10.3 for J-EX Series Ethernet Switches NOTE: For both J-SRX and J-EX devices, the browser and the network must support receiving and processing HTTP 1.1 GZIP compressed data. Layer 2 and Layer 3 Protocols • On J-EX8200 switches, ensure that the bfd-liveness-detection timers are set no lower than
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 58
    of flooding the message to all members of that VLAN. This problem occurs because the switch uses the standard forwarding database (FDB) with Redundant Routing Engines (CLI Procedure)" in the Dell PowerConnect J-Series Ethernet Switch Complete Software Guide for Junos OS Release 10.3. [PR/402109]
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 59
    new query returns very few results, the Results table continues to display page 3 and shows no results. To view the results, navigate to page 1 manually. [PR/476338] • In the J-Web interface, the dashboard does not display the uplink ports or uplink module ports unless transceivers are plugged into
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 60
    locations: • Maintain > Files > Log Files > Download • Maintain > Config Management > History • Maintain > Customer Support > Support Information > Generate Report • Troubleshoot > Troubleshoot Port > Generate Report • Monitor > Events and Alarms > View Events > Generate Report • Monitor > Routing
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 61
    /var directory appears full after some files in the /var/log directory are deleted. To avoid this problem, use the clear log filename command to clear the log files, instead of deleting them manually. [PR/496298: This issue has been resolved.] • On J-EX8200 switches, the show pfe statistics traffic
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 62
    Switching, the MAC learning log might not display information. [PR/535200: This issue has been resolved.] • J-EX Series Ethernet switches do not support the J-Web interface. [PR/561871: This issue has been resolved.] • J-EX4200 switches with an SFP+ line card installed do not properly display
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 63
    outstanding issues with the documentation. Infrastructure • Options ip and ip6 for the show pfe statistics command are not supported on J-EX Series Ethernet switches. Support for those options on the switches might be incorrectly indicated in the documentation. Related Documentation • New Features
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 64
    the hardware documentation for your product and the Junos OS documentation for PowerConnect J-Series J-EX Series and J-SRX Series products , see the following Dell support website: http://www.support.dell.com/manuals. If the information in the latest release notes differs from the information
  • Dell PowerConnect J-8216 | Release Notes JUNOS version 10.3 - Page 65
    Support Revision History 22 November 2010-Revision 2, Junos Release 10.3R2 © Copyright Dell Dell, Inc. is strictly forbidden. Trademarks used in this text: Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell trademarks, service marks, registered trademarks, or registered service marks are
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Junos
®
10.3 OS Release Notes for Dell
PowerConnect J-SRX Series Services
Gateways and J-EX Series Ethernet
Switches
Release 10.3R2
22 November 2010
These release notes accompany Release 10.3 of the Juniper Networks Junos operating
system (Junos OS) for Dell PowerConnect J-SRX Series Services Gateways and J-EX
Series Ethernet Switches. They describe device documentation and known problems
with the software.
You can also find these release notes at
.
Contents
Junos OS Release Notes for Dell PowerConnect J-SRX Series Services
Gateways
.......................................................
4
New Features in Junos OS Release 10.3 for J-SRX Series Services
Gateways
...................................................
4
Software Features
............................................
5
Advertising Bandwidth for Neighbors on a Broadcast Link Support
.........
5
Group VPN Interoperability with Cisco’s GET VPN
......................
5
Changes in Default Behavior and Syntax in Junos OS Release 10.3 for J-SRX
Series Services Gateways
......................................
6
Application Layer Gateways (ALGs)
..............................
7
AppSecure
..................................................
7
Chassis Cluster
..............................................
8
Command-Line Interface (CLI)
..................................
9
1