Dell PowerEdge 2950 Information Update - Page 13

TPM Failure - memory slots

Get Dell PowerEdge 2950 PDF manuals and user guides View all Dell PowerEdge 2950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Table 1-1. System Messages (continued) Message Causes Corrective Actions PCIe Training Error: Slot n Faulty or improperly installed PCIe card in the specified slot. Reseat the PCIe card in the specified slot number. See "Expansion Cards" in the Hardware Owner's Manual. If the problem persists, see "Getting Help" in the Hardware Owner's Manual. Remote Access Controller cable error or incorrect card in the RAC slot. RAC cables not connected, Check that the RAC cables or RAC card installed in are connected, and that the wrong expansion slot. RAC card is installed in the correct expansion slot. See "Installing a RAC Card" in the Hardware Owner's Manual. NOTE: All TPM information messages appear after the BMC option ROM has been loaded during POST. TPM configuration System now resets. operation honored. Information only. TPM Failure A Trusted Platform Module See "Getting Help" in the (TPM) function has failed. Hardware Owner's Manual. TPM operation is pending. Press I to Ignore or M to Modify to allow this change and reset the system. WARNING: Modifying could prevent security. Configuration change has been requested. Press I to continue system boot. Press M to modify the TPM setting and restart. Warning: Following faulty DIMMs are disabled: DIMM n1 n2 Total memory size is reduced. Faulty or improperly See "Troubleshooting seated memory module(s). System Memory" in the DIMMs are disabled in Hardware Owner's Manual. pairs, as indicated by the n1 and n2. Check both DIMMs for a possible fault. Information Update 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Information Update
13
PCIe Training
Error: Slot
n
Faulty or improperly
installed PCIe card in
the specified slot.
Reseat the PCIe card in the
specified slot number. See
“Expansion Cards” in the
Hardware Owner’s Manual
.
If the problem persists, see
“Getting Help” in the
Hardware Owner’s Manual
.
Remote Access
Controller cable
error or incorrect
card in the RAC
slot.
RAC cables not connected,
or RAC card installed in
wrong expansion slot.
Check that the RAC cables
are connected, and that the
RAC card is installed in the
correct expansion slot. See
“Installing a RAC Card” in
the
Hardware Owner’s
Manual.
NOTE:
All TPM information messages appear after the BMC option ROM has been
loaded during POST.
TPM configuration
operation honored.
System now resets.
Information only.
TPM Failure
A Trusted Platform Module
(TPM) function has failed.
See “Getting Help” in the
Hardware Owner’s Manual
.
TPM operation is
pending. Press I to
Ignore or M to
Modify to allow
this change and
reset the system.
WARNING: Modifying
could prevent
security.
Configuration change has
been requested.
Press
I
to continue system
boot. Press
M
to modify
the TPM setting and
restart.
Warning: Following
faulty DIMMs are
disabled:
DIMM
n
1
n
2
Total memory size
is reduced.
Faulty or improperly
seated memory module(s).
DIMMs are disabled in
pairs, as indicated by the
n
1
and
n
2
. Check both
DIMMs for a possible fault.
See “Troubleshooting
System Memory” in the
Hardware Owner’s Manual
.
Table 1-1.
System Messages
(continued)
Message
Causes
Corrective Actions