Dell PowerEdge R760XA Host Bus Adapter Users Guide HBA 355 and 350 Series - Page 33

Remove the Dell HBA350i Adapter

Get Dell PowerEdge R760XA PDF manuals and user guides View all Dell PowerEdge R760XA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

NOTE: To prevent damage to the card, you must hold the card by its edges only. 4. Press the HBA card onto the connector until it is firmly seated. 5. Press the release latch to secure the card to the sled. 6. Connect the SAS cable connectors to the card. NOTE: Ensure that you connect the cable according to the connector labels on the cable. If reversed, the cable does not function properly. 7. Route the SAS data cable through the clip on the card and through the channel on the inner side of the chassis. 8. Attach the connector that is labeled BP SAS to connector SAS A on the backplane, and attach the connector that is labeled CTRL SAS to SAS-cable on the controller card. 9. Install the system cover. 10. Insert the sled into the chassis and turn on the system and any attached MX chassis peripherals. Figure 21. Install Dell HBA350i MX Remove the Dell HBA350i Adapter Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. ● You have read and complied with the safety guidelines listed in Safety instructions. ● You have completed the procedures in Before working inside your system. Steps 1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 2. Remove the system cover. Installation and removal of cards 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
NOTE:
To prevent damage to the card, you must hold the card by its edges only.
4.
Press the HBA card onto the connector until it is firmly seated.
5.
Press the release latch to secure the card to the sled.
6.
Connect the SAS cable connectors to the card.
NOTE:
Ensure that you connect the cable according to the connector labels on the cable. If reversed, the cable does
not function properly.
7.
Route the SAS data cable through the clip on the card and through the channel on the inner side of the chassis.
8.
Attach the connector that is labeled BP SAS to connector SAS A on the backplane, and attach the connector that is labeled
CTRL SAS to SAS-cable on the controller card.
9.
Install the system cover.
10.
Insert the sled into the chassis and turn on the system and any attached MX chassis peripherals.
Figure 21. Install Dell HBA350i MX
Remove the Dell HBA350i Adapter
Prerequisites
CAUTION:
Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that are shipped with your product.
●
You have read and complied with the safety guidelines listed in
Safety instructions
.
●
You have completed the procedures in
Before working inside your system
.
Steps
1.
Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and
peripherals.
2.
Remove the system cover.
Installation and removal of cards
33