Dell PowerSwitch S5212F-ON Open Networking Hardware Diagnostic Guide April 201 - Page 11

ONIE installation instructions, ONIE expansion, ONIE installation, ONIE service discovery and OS

Get Dell PowerSwitch S5212F-ON PDF manuals and user guides View all Dell PowerSwitch S5212F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

3 ONIE installation instructions This section describes the different methods to install ONIE on your switch. NOTE: After installing the networking operating software (NOS) and diagnostics operating system (DIAG-OS), if you boot into ONIE Install mode, ONIE assumes ownership of the system; ONIE Install mode is sticky. In this situation, ONIE stays in Install mode until NOS and DIAG-OS are successfully installed again. If you want to boot into ONIE for any reason other than installation, use Rescue mode or Update mode. NOTE: To access ONIE, use the RJ-45 console port. ONIE expansion To view all the ONIE commands available, from the ONIE prompt, enter onie- and click twice. ONIE:/ # onie- onie-boot-mode onie-fwpkg onie-console onie-nos-install onie-discovery-start onie-self-update onie-discovery-stop onie-support onie-syseeprom onie-sysinfo onie-uninstaller Topics: • ONIE installation • ONIE service discovery and OS installation • Installation ONIE from BIOS ONIE installation The following steps describe how to load ONIE: • Installing ONIE-these instructions use the universal serial bus (USB) method. To boot from a Linux USB, you must preinstall BIOS on your system. • ONIE operates using a 115200 baud rate. Ensure that any equipment attached to the serial port supports the required 115200 baud rate. NOTE: The following output examples are for reference only; your output may vary. NOTE: The management port IP, FTP server IP address, MAC address, and user-id shown are for illustration purpose only. Use your system's applicable values. ONIE service discovery and OS installation ONIE attempts to locate the installer through several discovery methods. To download and run an installer, the ONIE Service Discovery feature follows these steps in order and uses the first successful method found: 1 Pass from the boot loader. 2 Search locally attached storage devices for one of the ONIE default installer filenames-for example, USB. 3 Discover the URLs from DHCPv4. 4 Report discovered URLs based on the DHCPv4 responses. 5 Query to the IPv6 link-local neighbors using HTTP for an installer. ONIE installation instructions 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
ONIE installation instructions
This section describes the
different
methods to install ONIE on your switch.
NOTE:
After installing the networking operating software (NOS) and diagnostics operating system (DIAG-OS), if you boot into
ONIE Install mode, ONIE assumes ownership of the system; ONIE Install mode is sticky. In this situation, ONIE stays in Install
mode until NOS and DIAG-OS are successfully installed again. If you want to boot into ONIE for any reason other than
installation, use Rescue mode or Update mode.
NOTE:
To access ONIE, use the RJ-45 console port.
ONIE expansion
To view all the ONIE commands available, from the ONIE prompt, enter
onie-
and click
<tab>
twice.
ONIE:/ # onie-
<TAB><TAB>
onie-boot-mode
onie-fwpkg
onie-syseeprom
onie-console
onie-nos-install
onie-sysinfo
onie-discovery-start
onie-self-update
onie-uninstaller
onie-discovery-stop
onie-support
Topics:
•
ONIE installation
•
ONIE service discovery and OS installation
•
Installation ONIE from BIOS
ONIE installation
The following steps describe how to load ONIE:
•
Installing ONIE—these instructions use the universal serial bus (USB) method. To boot from a Linux USB, you must preinstall BIOS on
your system.
•
ONIE operates using a 115200 baud rate. Ensure that any equipment attached to the serial port supports the required 115200 baud rate.
NOTE:
The following output examples are for reference only; your output may vary.
NOTE:
The management port IP, FTP server IP address, MAC address, and user-id shown are for illustration purpose only. Use
your system’s applicable values.
ONIE service discovery and OS installation
ONIE attempts to locate the installer through several discovery methods.
To download and run an installer, the ONIE Service Discovery feature follows these steps in order and uses the
first
successful method
found:
1
Pass from the boot loader.
2
Search locally attached storage devices for one of the ONIE default installer
filenames—for
example, USB.
3
Discover the URLs from DHCPv4.
4
Report discovered URLs based on the DHCPv4 responses.
5
Query to the IPv6 link-local neighbors using HTTP for an installer.
3
ONIE installation instructions
11