Dell Precision M6800 Owners Manual - Page 48

Removing the Input/Output (I/O) Board, Installing the I/O Board

Get Dell Precision M6800 PDF manuals and user guides View all Dell Precision M6800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Removing the Input/Output (I/O) Board 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) SD card b) battery c) base cover d) keyboard trim e) keyboard f) optical drive g) primary and secondary hard drive h) palmrest 3. Perform the following steps to remove the I/O board: a) Disconnect the ExpressCard module connector from the I/O board. b) Remove the screw that secures the I/O board to the computer. c) Lift the right edge of the I/O board upwards to disengage the connector and remove it from computer. Installing the I/O Board 1. Connect the I/O board connector and slide the I/O board into its slot in the computer. 2. Tighten the screw to secure the I/O board to the computer. 3. Connect the ExpressCard module connector to the I/O board. 4. Install the: a) palmrest b) primary and secondary hard drive c) optical drive 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Removing the Input/Output (I/O) Board
1.
Follow the procedures in
Before Working Inside Your Computer
.
2.
Remove the:
a)
SD card
b)
battery
c)
base cover
d)
keyboard trim
e)
keyboard
f)
optical drive
g)
primary and secondary hard drive
h)
palmrest
3.
Perform the following steps to remove the I/O board:
a)
Disconnect the ExpressCard module connector from the I/O board.
b)
Remove the screw that secures the I/O board to the computer.
c)
Lift the right edge of the I/O board upwards to disengage the connector and remove it from computer.
Installing the I/O Board
1.
Connect the I/O board connector and slide the I/O board into its slot in the computer.
2.
Tighten the screw to secure the I/O board to the computer.
3.
Connect the ExpressCard module connector to the I/O board.
4.
Install the:
a)
palmrest
b)
primary and secondary hard drive
c)
optical drive
48