Dell Z9264F-ON EMC PowerSwitch Setup Guide - Page 8

Z9264F-ON switch installation, Unpack, Ground lug assembly

Get Dell Z9264F-ON PDF manuals and user guides View all Dell Z9264F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

3 Z9264F-ON switch installation To install the Z9264F-ON switch, complete the installation procedures in the order presented in this section. Always handle the switch and its components with care. Avoid dropping the switch or any field replaceable units (FRUs). NOTE: ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when handling the switch and its components. As with all electrical devices of this type, take all the necessary safety precautions to prevent injury when installing this switch. Topics: • Unpack • Ground lug assembly • Four-post rack assembly • Four-post rack mount • Optics installation • Switch startup • After switch installation Unpack NOTE: Before unpacking the switch, inspect the container and immediately report any evidence of damage. When unpacking the Z9264F-ON switch, make sure that the following items are included: ● One Z9264F-ON switch ● One RJ-45 to DB-9 female cable ● Two sets of rail kits, no tools required ● Two PSUs ● Four fan units ● Two AC power cables, country or region specific ● DC switches only: DC power ground lug kit ● Z9264F-ON Set-up Guide ● Safety and Regulatory Information ● Warranty and Support Information 1. Place the container on a clean, flat surface and cut all straps securing the container. 2. Open the container or remove the container top. 3. Carefully remove the switch from the container and place it on a secure and clean surface. 4. Remove all packing material. 5. Inspect the product and accessories for damage. Ground lug assembly Before you install the switch into a rack, install the ground (GND) lug assembly. NOTE: For AC-powered switches, although the third conductor of the AC power cable provides a ground path, Dell EMC recommends grounding your switch with a dedicated ground wire. You can order an AC ground lug separately. NOTE: For a DC-powered switch, the only way to safely ground your switch is to attach a dedicated ground wire. The ground lug kit ships in a plastic bag that is placed with the other accessories inside the shipping box. The ground lug bracket 8 Z9264F-ON switch installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
Z9264F-ON switch installation
To install the Z9264F-ON switch, complete the installation procedures in the order presented in this section.
Always handle the switch and its components with care. Avoid dropping the switch or any field replaceable units (FRUs).
NOTE:
ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap
when handling the switch and its components. As with all electrical devices of this type, take all the necessary safety
precautions to prevent injury when installing this switch.
Topics:
•
Unpack
•
Ground lug assembly
•
Four-post rack assembly
•
Four-post rack mount
•
Optics installation
•
Switch startup
•
After switch installation
Unpack
NOTE:
Before unpacking the switch, inspect the container and immediately report any evidence of damage.
When unpacking the Z9264F-ON switch, make sure that the following items are included:
●
One Z9264F-ON switch
●
One RJ-45 to DB-9 female cable
●
Two sets of rail kits, no tools required
●
Two PSUs
●
Four fan units
●
Two AC power cables, country or region specific
●
DC switches only: DC power ground lug kit
●
Z9264F-ON Set-up Guide
●
Safety and Regulatory Information
●
Warranty and Support Information
1.
Place the container on a clean, flat surface and cut all straps securing the container.
2.
Open the container or remove the container top.
3.
Carefully remove the switch from the container and place it on a secure and clean surface.
4.
Remove all packing material.
5.
Inspect the product and accessories for damage.
Ground lug assembly
Before you install the switch into a rack, install the ground (GND) lug assembly.
NOTE:
For AC-powered switches, although the third conductor of the AC power cable provides a ground path, Dell EMC
recommends grounding your switch with a dedicated ground wire. You can order an AC ground lug separately.
NOTE:
For a DC-powered switch, the only way to safely ground your switch is to attach a dedicated ground wire. The
ground lug kit ships in a plastic bag that is placed with the other accessories inside the shipping box. The ground lug bracket
3
8
Z9264F-ON switch installation