Denon AVR-486S Owners Manual - Page 15

System Setup - avr 486 remote

Page 15 highlights

ENGLISH System Setup Use System Setup to customize a variety of settings to suit your listening environment. For the contents of a system menu and the initial setting of this unit ( page 17). Front display • You can change the settings using the buttons on the remote control unit. • The AVR-486 is equipped with an alpha numeric front panel display that can also be used to check and adjust settings. Some representative front display examples are shown below. System Setup Setting the Speaker Configuration The composition of the signals output to each channel and the frequency response are adjusted automatically according to the combination of speakers actually being used. 1 Press the CURSOR F or G button to select your front speaker type, then press the ENTER or CURSOR H button to switch to the center speaker setting. MODE 1 SETUP ENTER CURSOR [ Display ] *COAX1 Currently selected line No. CD Current setting Press the CURSOR F button to execute. *TEST TONE Yes< Currently selected line 1 Set the MODE 1 switch to "AUDIO". 2 Press the SETUP button to enter the setting. *System Setup 3 Press the ENTER or CURSOR H button to select the setting, then press the CURSOR F or G button to select the parameter. *Front Large Large Small 4 Press the ENTER or CURSOR H button to confirm the new settings. *Front Large Large Small 2 Press the CURSOR F or G button to select your center speaker type, then press the ENTER or CURSOR H button to switch to the surround speaker setting. *Center Small Large Small None When "Small" has been selected for the front speakers, "Large" cannot be selected for the center speaker. 3 Press the CURSOR F or G button to select your surround speaker type, then press the ENTER or CURSOR H button to switch to the surround back speaker setting. *Center Small Large Small None 5 Press the SETUP button to finish system set up. *Surr. Small Large Small None When "Small" has been selected for the front speakers, "Large" cannot be selected for the surround speakers. 12 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53

System Setup
ENGLISH
ENGLISH
12
Use System Setup to customize a variety of settings to suit your listening environment.
For the contents of a system menu and the initial setting of this unit (
page 17).
You can change the settings using the buttons on the remote control unit.
The AVR-486 is equipped with an alpha numeric front panel display that can also be used to check and adjust settings. Some
representative front display examples are shown below.
CURSOR
MODE 1
SETUP
ENTER
Front display
System Setup
No.
*TEST TONE Yes<
Press the
CURSOR
F
button to execute.
Currently selected line
*COAX1
CD
Current setting
Currently selected line
1
Set the
MODE 1
switch to “AUDIO”.
2
Press the
SETUP
button to enter the setting.
4
Press the
ENTER
or
CURSOR
H
button to confirm
the new settings.
*System Setup
3
Press the
ENTER
or
CURSOR
H
button to select
the setting, then press the
CURSOR
F
or
G
button to select the parameter.
*Front
Large
Large
Small
*Center
Small
Large
Small
None
5
Press the
SETUP
button to finish system set up.
[ Display ]
Setting the Speaker Configuration
1
Press the
CURSOR
F
or
G
button to select your
front speaker type, then press the
ENTER
or
CURSOR
H
button to switch to the center speaker
setting.
*Front
Large
Large
Small
2
Press the
CURSOR
F
or
G
button to select your
center speaker type, then press the
ENTER
or
CURSOR
H
button to switch to the surround
speaker setting.
*Center
Small
Large
Small
None
When
Small
has been selected for the front speakers,
Large
cannot be selected for the center speaker.
3
Press the
CURSOR
F
or
G
button to select your
surround speaker type, then press the
ENTER
or
CURSOR
H
button to switch to the surround
back speaker setting.
*Surr.
Small
Large
Small
None
When
Small
has been selected for the front speakers,
Large
cannot be selected for the surround speakers.
The composition of the signals output to each channel and the
frequency response are adjusted automatically according to the
combination of speakers actually being used.