Denon AVR-5803/AVR-5803A Owners Manual - Page 21

Selecting the surround speakers for the different surround modes, Setting the Crossover Frequency

Get Denon AVR-5803/AVR-5803A PDF manuals and user guides View all Denon AVR-5803/AVR-5803A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

• Parameters Large Select this when using speakers that can fully reproduce low sounds of below 80 Hz. Small Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer. None Select this when no speakers are installed. Yes/No Select "Yes" when a subwoofer is installed, "No" when a subwoofer is not installed. 2spkrs/1spkr.....Select the number of speakers to be used for the surround back channel. If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when "Small" is set for the front, center and surround speakers. To take full advantage of the performance of the Home THX certified speaker systems, set the front, center and surround speaker size parameters to "Small" and the subwoofer to "Yes". For the majority of speaker system configurations, using the SMALL setting for all five main speakers and Subwoofer On with a connected subwoofer will yield the best results. When "Front" is set to "Small", "Subwoofer" is automatically set to "Yes", and when "Subwoofer" is set to "No", "Front" is automatically set to "Large". Selecting the surround speakers for the different surround modes • At this screen preset the surround speakers to be used in the different surround modes. 1 When either "Large" or "Small" has been set for both speakers A and B on the System Setup Menu (when using both A and B surround speakers), the surround speaker setting screen appears. Select the surround speakers to be used in the different surround modes. • To select the surround mode • To select the surround speaker A: When using surround speakers A B: When using surround speakers B A+B: When using both surround speakers A and B 2 Enter the setting. When "Front" is set to "Large" and "Subwoofer" is set to "Yes", the set switches to the subwoofer mode. Speaker type setting when using both surround speakers A and B If "Small" is set for either surround speakers A or B, the output is the same as when "Small" is set for both A and B. For the "WIDE SCREEN" and "5/7CH STEREO" DSP simulation modes, the surround speakers can be set separately. Setting the Crossover Frequency Set the crossover frequency and subwoofer mode according to the speaker system being used. 1 Select the Crossover Frequency mode. To select the Crossover Frequency. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
21
•
Parameters
Large
................
Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small
................
Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume.
When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None
……
.........
Select this when no speakers are installed.
Yes/No
…
..........
Select
“
Yes
”
when a subwoofer is installed,
“
No
”
when a subwoofer is not installed.
2spkrs/1spkr
.....
Select the number of speakers to be used for the surround back channel.
If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when
“
Small
”
is set for the front, center
and surround speakers.
To take full advantage of the performance of the Home THX certified speaker systems, set the front, center and surround speaker size
parameters to
“
Small
”
and the subwoofer to
“
Yes
”
.
For the majority of speaker system configurations, using the SMALL setting for all five main speakers and Subwoofer On with a connected
subwoofer will yield the best results.
When
“
Front
”
is set to
“
Small
”
,
“
Subwoofer
”
is automatically set to
“
Yes
”
, and when
“
Subwoofer
”
is set to
“
No
”
,
“
Front
”
is automatically
set to
“
Large
”
.
Selecting the surround speakers for the different surround modes
•
At this screen preset the surround speakers to be used in the different surround modes.
1
When either
“
Large
”
or
“
Small
”
has been set for both speakers A and B
on the System Setup Menu (when using both A and B surround speakers),
the surround speaker setting screen appears.
Select the surround speakers to be used in the different surround modes.
•
To select the surround mode
•
To select the surround speaker
A:
When using surround speakers A
B:
When using surround speakers B
A+B:
When using both surround speakers A and B
2
Enter the setting.
When
“
Front
”
is set to
“
Large
”
and
“
Subwoofer
”
is set to
“
Yes
”
, the set switches to the subwoofer mode.
Speaker type setting when using both surround speakers A and B
If
“
Small
”
is set for either surround speakers A or B, the output is the same as when
“
Small
”
is set for both A and B.
For the
“
WIDE SCREEN
”
and
“
5/7CH STEREO
”
DSP simulation modes, the surround speakers can be set separately.
Setting the Crossover Frequency
1
Select the Crossover Frequency mode.
Set the crossover frequency and subwoofer mode according to the speaker system being used.
To select the Crossover Frequency.