Denon AVR-5803/AVR-5803A Owners Manual - Page 33

Setting the Ext. In Setup, S.Back, SW Level, INPUT Vol.

Get Denon AVR-5803/AVR-5803A PDF manuals and user guides View all Denon AVR-5803/AVR-5803A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Setting the Ext. In Setup • Set the method of playback of the analog input signal connected to the Ext.In-1 and Ext.In-2 terminal. 1 At the System Setup Menu select "Ext.In Setup". 2 Switch to the Ext.In Setup screen. 3 q Select the input terminal. w Switch to the setting screen. 4 Select the item to be set (push the jog stick to the up and down) then select the parameter (push the jog stick to the left and right). MODE: DSP: The analog input signal is converted into a digital signal and undergoes DSP processing. System Setup settings (speaker configuration, channel delay, etc.) are reflected in the same way as for other input signals. ANALOG: The analog input signal is played without DSP processing. SW and center channel: Down-mixing is conducted by the analog circuit. Surround and surround back channels: Not output if "No" is selected at the speaker configuration. Channel delay: Not reflected. S.Back: Set when MODE is set to DSP. Select according to the specifications of the player being used. Also refer to the player's operating instructions. NOT USE: Select when neither SBL or SBR is connected. SB (SBL): Select when only one surround back channel (SBL) is connected. SBL/SBR: Select when two surround back channels (SBL and SBR) are connected. SW Level: Select according to the specifications of the player being used. Also refer to the player's operating instructions. +15dB (default) recommended. (0, +5, 10 and +15 can be selected.) INPUT Vol.: Set when MODE is set to DSP. If the OVER LOAD indicator is displayed on the fluorescent tube, adjust the input level to between 0 and -20 dB. 5 Enter the setting. The System Setup Menu reappears. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
33
Setting the Ext. In Setup
•
Set the method of playback of the analog input signal connected to the Ext.In-1 and Ext.In-2 terminal.
1
At the System Setup Menu select
“
Ext.In Setup
”
.
2
Switch to the Ext.In Setup screen.
3
q
Select the input terminal.
w
Switch to the setting screen.
MODE:
DSP:
The analog input signal is converted into a digital signal and undergoes DSP processing.
System Setup settings (speaker configuration, channel delay, etc.) are reflected in the same way as for other input signals.
ANALOG:
The analog input signal is played without DSP processing.
SW and center channel: Down-mixing is conducted by the analog circuit. Surround and surround back channels: Not output
if
“
No
”
is selected at the speaker configuration. Channel delay: Not reflected.
S.Back:
Set when MODE is set to DSP. Select according to the specifications of the player being used. Also refer to the player
’
s operating
instructions.
NOT USE: Select when neither SBL or SBR is connected.
SB (SBL):
Select when only one surround back channel (SBL) is connected.
SBL/SBR:
Select when two surround back channels (SBL and SBR) are connected.
SW Level:
Select according to the specifications of the player being used. Also refer to the player
’
s operating instructions.
+15dB (default) recommended. (0, +5, 10 and +15 can be selected.)
INPUT Vol.:
Set when MODE is set to DSP.
If the OVER LOAD indicator is displayed on the fluorescent tube, adjust the input level to between 0 and -20 dB.
5
Enter the setting.
The System Setup Menu reappears.
4
Select the item to be set (push the jog stick to the
up and down) then select the parameter (push the
jog stick to the left and right).