Denon AVR-5803/AVR-5803A Owners Manual - Page 7

Connecting the audio components • When making connections, also refer to the operating instructions of the other components. CD recorder or Tape deck 1 B OUTPUT INPUT R LRL R LR L MD recorder or Tape deck 2 OUTPUT INPUT R LRL R LR L Connecting a tape deck Connections for recording: Connect the tape deck's recording input jacks (LINE IN or REC) to this unit's tape recording (OUT) jacks using pin plug cords. Connections for playback: Connect the tape deck's playback output jacks (LINE OUT or PB) to this unit's tape playback (IN) jacks using pin plug cords. Connecting the pre-out jacks Use these jacks if you wish to connect external power amplifier(s) to increase the power of the front, center, surround and surround back sound channels, or for connection to powered loudspeakers. When using only one surround back speaker, connect it to left channel. CD player DIGITAL AUDIO OUTPUT RL RL Connecting the AC OUTLETS AC OUTLETS • SWITCHED (total capacity - 120 W (1 A.)) The power to these outlets is turned on and off in conjunction with the POWER switch on the main unit, and when the power is switched between on and standby from the remote control unit. No power is supplied from these outlets when this unit's power is at standby. Never connect equipment whose total capacity is above 120 W (1 A.) NOTE: Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other electrical appliances. AC cord (Supplied) AC outlets (wall) AC 120V, 60Hz Connecting a CD player Connect the CD player's analog output jacks (ANALOG OUTPUT) to this unit's CD jacks using pin plug cords. Turntable (MM cartridge) FRONT R CENTER SURR.-A R SURR.-B R SURR. BACK R MULTI ZONE 2 R SPEAKER SYSTEMS CONPONENT VIDEO IN DVD IN TV IN DBS / SAT MONITOR OUT Y PB/CB PR/CR Y PB/CB PR/CR Y PB/CB PR/CR Y PB/CB PR/CR ANTENNA TERMINALS AM LOOP ANT. FMCOAX. 75Ω L R SIGNAL PHONO GND MULTI ZONE DVD VDP 1 VIDEO OUT S-VIDEO CD L DVD VDP R FRONT CENTER SURR. L TV DBS / V. AUX VCR-1 VCR-2 VCR-3 VCR-1 VCR-2 VCR-3 SAT MONITOR 1 2 AC IN L LR IN OUT OUT AUDIO IN R OUT IN DBS / CDR / MD / TV SAT V. AUX VCR-1 VCR-2 VCR-3 VCR-1 VCR-2 VCR-3 TAPE-1 TAPE-2 L L R R SURR. SURR. SURR. CDR / MD / BACK FRONT CENTER SURR. BACK FRONT CENTER SURR. BACK TAPE-1 TAPE-2 MULTI ZONE 1 2 L L R SW IN DOLBY DIGITAL RF EXT. IN-1 L RIN DENON LINK 1 ROOM TO ROOM POWER AMP (REMOTE CONTROL) CONTROL OUT IN OUT SW EXT. IN-2 IN 2 3 4 5 EXT. IN COAXIAL 1 2 RS-232C TRIGGER OUT DC 12V 20mA MAX. SW PRE OUT 3 4 5 OPTICAL DIGITAL R R OUT PREOUT OUT OUT 6 5 6 FRONT L SURR.-A L SURR.-B L SURR. BACK L MULTI ZONE 2 L SPEAKER IMPEDANCE FRONT, CENTER, SURR. BACK MULTI ZONE 2 / 6 16Ω SURROUND A OR B / 6 16Ω A + B / 8 16Ω SPEAKER SYSTEMS SWITCHED TOTAL 120W (1A.) MAX. AC 120V 60Hz AC OUTLETS Ground wire Connecting a turntable Extension jacks for future use Connect the turntable's output cord to the AVR-5803's PHONO jacks, the L (left) plug to the L jack, the R (right) plug to the right jack. OUTPUT INPUT OPTICAL MD recorder, DAT deck or other component equipped with digital input/output jacks B NOTE: This unit cannot be used with MC cartridges directly. Use a separate head amplifier or step-up transformer. If humming or other noise is generated when the ground wire is connected, disconnect the ground wire. Denon Link terminal Use this terminal to connect a Denon DVD player for high quality digital multichannel sound. For details, refer to the DVD player's operating instructions. COAXIAL OPTICAL OUTPUT DIGITAL AUDIO CD player or other component equipped with digital output jacks Connecting the DIGITAL jacks Use these for connections to audio equipment with digital output. Refer to page 29 for instructions on setting this terminal. NOTES: • Use 75 Ω/ohms cable pin cords for coaxial connections. • Use optical cables for optical connections, removing the cap before connecting. DIGITAL EXT. IN Extended function for future use. 7