Denon AVR3310CI Owners Manual Addendum - English - Page 14

Getting Started Connections Settings Playback Information Unavailable Functions After Upgrading Specifications ENGLISH Adjusting the Sound and Picture Quality (Audio/Video Adjust) Setting items Surround Parameters (Continued) Tone Adjust the tonal quality of the sound. Setting contents • This can also be set by pressing STANDARD. • If the source being played contains a surround back signal, the decoder type is automatically selected by the AFDM function. Set "AFDM" to "OFF" to switch to your preferred decoder. • If the setting in "Speaker Configuration" - "Surround Back" (vpage 9) is "None", "Surround Back" is not displayed. Subwoofer Att. : Attenuate subwoofer level when using EXT. IN input. • ON : Set. • OFF : Do not set. Usually use in this mode. Set this to "ON" if the subwoofer channel level seems too high when playing audio signal. Subwoofer : Turn subwoofer output on and off. • ON : The subwoofer is used. • OFF : The subwoofer is not used. Default : Restores all the surround parameter settings to their defaults. • No : Do not reset to the defaults. • Yes : Reset to the defaults. Tone Control : Sets the tone control function ON and OFF. • ON : Allow tone adjustment (treble, bass). • OFF : Playback without tone adjustment. • This can be set when "Dynamic EQ" (vpage 14) is set to "OFF". • The tone cannot be adjusted in the direct mode. Bass : Adjust low frequency range (bass). • -6dB ~ +6dB This can be set when "Tone Control" (vpage 13) is set to "ON". Treble : Adjust high frequency range (treble). • -6dB ~ +6dB This can be set when "Tone Control" (vpage 13) is set to "ON". Setting items Audyssey Settings Set Audyssey MultEQ®, Audyssey Dynamic EQ® and Audyssey Dynamic Volume™. NOTE If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed. In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 33 of GThe original versionH Operating Instructions) to return to the settings after Audyssey Auto Setup was run. Setting contents MultEQ : Corrects both time and frequency response problems in the listening area. • Audyssey : Optimize the frequency response of all speakers. • Audyssey Byp.L/R : Optimize frequency response of speakers except front L and R speakers. • Audyssey Flat : Optimize frequency response of all speakers to flat response. • Manual : Apply frequency response set with "Manual EQ" (vpage 16). • OFF : Turn "MultEQ" equalizer off. • "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be selected after Audyssey Auto Setup has been performed. "Audyssey" is automatically selected after performing Audyssey Auto Setup. "When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, " " lights. • After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers measured, only " " lights. • If "Dynamic EQ" or "Dynamic Volume" is set to "ON" when "MultEQ" is set to either "OFF" or "Manual", "MultEQ" is automatically set to "Audyssey". • You can also press MULTEQ to set. NOTE • "MultEQ" and "Manual EQ" cannot be selected when "EQ Customize" is set to "Not Used" (vpage 38 of GThe original versionH Operating Instructions). • When using headphones, "MultEQ" is set to "OFF". 13 Main remote control operation buttons :Displaying the menu Cancel the menu :Moves the cursor (Up/Down/Left/Right) :Confirm the setting :Return to previous menu