Denon S1000 Operating Instructions - Page 11

5 BASIC OPERATION Play and pause • Each push of the y PLAY/PAUSE (13) button switches between playback and pause. y PLAY/PAUSE (13) button illuminates solid green during playback and flashed in pause. • When the y PLAY/PAUSE (13) button is pushed during play, the DN-S1000 pauses playback at that point. Push y PLAY/PAUSE (13) button once again and playback resumes. • Playback will pause when SCRATCH is selected with the !8 DISC MODE button and the scratch disc is held with your hand. Playback resumes when your hand is released. Push the !8 DISC MODE button to set o Scratch DISC MODE 2 Disc to search mode. The ON : SCRATCH OFF : SEARCH/ !8 DISC MODE button BEND LEDs will turn off. Turn the o Scratch Disc to change Cue point. You can hear the short sound of the current 3 Cue point. When o Scratch Disc is turned in the pause, Cue or frame repeat mode, it works as the manual search function. Play and Cue • When the i CUE button is pushed during playback, the track stops and returns to the original position of which playback started from, the (Cue point). This function is also called Back-Cue. With the Back-Cue function, you can start from exactly same position. The i CUE button illuminates solid red when DNS1000 is ready to start playback. • You can set and change Cue point as follows. • When you started playback. • Track select finished. • manual search. After you found your preferred Cue point, push 4 the i CUE button then a new Cue point is set. CUE CUE/STUTTER Adjusting the pitch • With Pitch slider you can adjust the playback speed (Pitch). • If you would not prefer to change key of sound, use the Key Adjust function. Select the track • Turn the @3 TRACK knob. • By pushing @3 TRACK knob down while turning, the tracks will increment 10 at a time. !Move the Cue point • If you would like to start playback other from the beginning of the track, you need to move Cue Point using fast Search and manual search function. You can move to the approximate playback start position by @4 or @5 FAST SEARCH buttons. [QUICK JUMP] QUICK JUMP • If the FAST SEARCH button is tapped shortly, the FAST SEARCH 1 playback position jumps about 10 seconds. The jump time can be selected in the preset mode from 10,20,30 or 60 sec. [FAST SEARCH] • When the FAST SEARCH button is pressed and held in, the disc is fast-searched. Push the @9 PITCH/KEY PITCH/KEY button to PITCH LED lights up. 1 RANGE • PITCH → KEY (key adjust) → OFF 20 Pitch decreases Move the @8 Pitch slider to adjust the pitch. The current pitch setting is displayed on the display. Pitch increases DN-S1000 has five pitch ranges, 4%, 10%, 16%, 24% and 100%. When the @9 RANGE button is pushed for more than 1 sec, 3 the pitch range can be selected PITCH/KEY with the @3 PARAMETERS knob. RANGE • When the @3 PARAMETERS knob is pushed the pitch 3 range is entered and the pitch range selection mode is cancelled. PARAMETERS PUSH TRACK SEARCH MP3 SEARCH MODE Pitch Bend • With PITCH BEND function you can change pitch temporary. DN-S1000 has two ways for this function PITCH BEND buttons and Scratch Disc. [PITCH BEND +/- buttons] • Push the @6 PITCH BEND - or @7 + button for momentary change of 1 pitch. PITCH BEND While holding these buttons down, the pitch continues to change up to the limitation. • After releasing the PITCH BEND buttons, playback pitch returns to slider setting. [Scratch Disc] • When the disc mode is set to SEARCH/BEND with the !8 DISC MODE button, the playback speed 2 can be changed by turning o Scratch Disc during playback. Power on play • When "POWER ON PLAY" is set to "ON" at "⁄4 PRESET (10)", playback starts from the first track on the disc when the power is turned on. ENGLISH 11