Dewalt D55168 Instruction Manual - Page 18

POSSIBLE CAUSE, POSSIBLE SOLUTION, Air Filter, Maintenance - lowes

Get Dewalt D55168 PDF manuals and user guides View all Dewalt D55168 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

English CODE POSSIBLE CAUSE 16 Extension cord is wrong length or gauge 17 Loose electrical connections 18 Possible defective motor 19 Paint spray on internal motor parts 20 Pressure release valve on pressure switch has not unloaded head pressure 21 Fuse blown, circuit breaker tripped 22 Worn Belt 23 Restricted air intake filter 18 POSSIBLE SOLUTION Check for proper gauge wire and cord length under Extension Cords. Check wiring connection inside pressure switch and terminal box area. Contact a DEWALT factory service center or a DEWALT authorized service center. Contact a DEWALT factory service center or a DEWALT authorized service center. Do not operate the compressor in the paint spray area. See flammable vapor warning. Bleed the line by pushing the lever on the pressure switch to the "O" position; if the valve does not open, replace switch. 1. Check fuse box for blown fuse and replace as necessary. Reset circuit breaker. Do not use a fuse or circuit breaker with higher rating than that specified for our particular branch circuit. 2. Check for proper fuse. You should use a time delay fuse. 3. Check for low voltage conditions and/or proper extension cord. 4. Disconnect the other electrical appliances from circuit or operate the compressor on its own branch circuit. Contact a DEWALT factory service center or a DEWALT authorized service center. Clean or replace air intake filter. Do not operate the air compressor with the filter removed. Refer to the Air Filter paragraph in the Maintenance section.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
18
English
CODE
POSSIBLE CAUSE
POSSIBLE SOLUTION
16
Extension cord is wrong length or gauge
Check for proper gauge wire and cord length under
Extension
Cords
.
17
Loose electrical connections
Check wiring connection inside pressure switch and terminal
box area.
18
Possible defective motor
Contact a D
E
WALT factory service center or a D
E
WALT
authorized service center.
19
Paint spray on internal motor parts
Contact a D
E
WALT factory service center or a D
E
WALT
authorized service center. Do not operate the compressor in
the paint spray area.
See flammable vapor warning.
20
Pressure release valve on pressure switch has not
unloaded head pressure
Bleed the line by pushing the lever on the pressure switch to
the "O" position; if the valve does not open, replace switch.
21
Fuse blown, circuit breaker tripped
1. Check fuse box for blown fuse and replace as necessary.
Reset circuit breaker. Do not use a fuse or circuit breaker
with higher rating than that specified for our particular
branch circuit.
2. Check for proper fuse. You should use a time
delay fuse.
3. Check for low voltage conditions and/or proper
extension cord.
4. Disconnect the other electrical appliances from
circuit or operate the compressor on its own
branch circuit.
22
Worn Belt
Contact a D
E
WALT factory service center or a D
E
WALT
authorized service center.
23
Restricted air intake filter
Clean or replace air intake
filter. Do not operate the air
compressor with the filter removed. Refer to the
Air Filter
paragraph in the
Maintenance
section.