Dewalt DW712 Parts Diagram - Page 11

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT. Horst Grossmann Vice President Engineering and Product Development DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Germany 01.01.2012 Safety Instructions WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury including the following. Read all these instructions before attempting to operate this product and save these instructions. SAVE THIS MANUAL FOR FUTURE REFERENCE General Safety Rules 1. Keep work area clear. Cluttered areas and benches invite injuries. 2. Consider work area environment. Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the work area well lit (250-300 Lux). Do not use the tool where there is a risk of causing fire or explosion, e.g., in the presence of flammable liquids and gases. 3. Guard against electric shock. Avoid body contact with earthed surfaces (e.g., pipes, radiators, cookers and refrigerators). When using the tool under extreme conditions (e.g., high humidity, when metal swarf is being produced, etc.), electric safety can be improved by inserting an isolating transformer or a (FI) earth-leakage circuit-breaker. 4. Keep other persons away. Do not let persons, especially children, not involved in the work, touch the tool or the extension cord and keep them away from the work area. 5. Store idle tools. When not in use, tools must be stored in a dry place and locked up securely, out of reach of children. 6. Do not force the tool. It will do the job better and safer at the rate to which it was intended. 7. Use the right tool. Do not force small tools to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example do not use circular saws to cut tree limbs or logs. 8. Dress properly. Do not wear loose clothing or jewellery, as these can be caught in moving parts. Non-skid footwear is recommended when working outdoors. Wear protective hair covering to contain long hair. 9. Use protective equipment. Always use safety glasses. Use a face or dust mask if working operations create dust or flying particles. If these particles might be considerably hot, also wear a heat-resistant apron. Wear ear protection at all times. Wear a safety helmet at all times. 10. Connect dust extraction equipment. If devices are provided for the connection of dust extraction and collecting equipment, ensure these are connected and properly used. 11. Do not abuse the cord. Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges. Never carry the tool by its cord. ENGLISH 12. Secure work. Where possible use clamps or a vice to hold the work. It is safer than using your hand and it frees both hands to operate the tool. 13. Do not overreach. Keep proper footing and balance at all times. 14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tools periodically and if damaged have them repaired by an authorized service facility. Keep handles and switches dry, clean and free from oil and grease. 15. Disconnect tools. When not in use, before servicing and when changing accessories such as blades, bits and cutters, disconnect tools from the power supply. 16. Remove adjusting keys and wrenches. Form the habit of checking to see that adjusting keys and wrenches are removed from the tool before operating the tool. 17. Avoid unintentional starting. Do not carry the tool with a finger on the switch. Be sure that the tool is in the "off" position before plugging in. 18. Use outdoor extension leads. Before use, inspect the extension cable and replace if damaged. When the tool is used outdoors, use only extension cords intended for outdoor use and marked accordingly. 19. Stay alert. Watch what you are doing. Use common sense. Do not operate the tool when you are tired or under the influence of drugs or alcohol. 20. Check for damaged parts. Before use, carefully check the tool and mains cable to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service centre unless otherwise indicated in this instruction manual. Have defective switches replaced by an authorized service centre. Do not use the tool if the switch does not turn it on and off. Never attempt any repairs yourself. WARNING! The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury. 21. Have your tool repaired by a qualified person. This electric tool complies relevant safety rules. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user. Additional Safety Rules for Mitre Saws • The machine is provided with a special configured power supply cord which can only be replaced by the manufacturer or its authorised service agent. • Do not use the saw to cut other materials than those recommended by the manufacturer. • Do not operate the machine without guards in position, or if guards are not in good working order or are not properly maintained. • Ensure that the arm is securely fixed when performing bevel cuts. • Keep the floor area around the machine level, well-maintained and free of loose materials, e.g., chips and cut-offs. • Use correctly sharpened saw blades. Ensure the speed marked on the saw blade is at least equal to the speed marked on the rating plate of the saw. • Make sure all locking knobs and clamp handles are tight before starting any operation. • Never place either hand in the blade area when the saw is connected to the electrical power source. 9