Dewalt DW7440RS Instruction Manual - Page 5

Table Saw Bracket Mounting - used

Get Dewalt DW7440RS PDF manuals and user guides View all Dewalt DW7440RS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

English Table Saw Bracket Mounting WARNING: To reduce the risk of injury, turn unit off, disconnect machine from power source before assembling the table saw to the table saw stand. An accidental start-up can cause injury. WARNING: For your own safety, read and understand the table saw instruction manual before using. Failure to heed these warnings may result in personal injury and serious damage to the table saw and the accessory. WARNING: The saw mounting brackets provided with this stand are equipped with lever locks. To reduce the risk of injury, DO NOT modify the mounting bracket lever locks. G 1. Unfold the legs by depressing R the leg release levers (F). Rotate the legs until the locking pin (G) clicks into its detent (R). H F 2. Turn the stand upright. The stand should be stable and should not rock. WARNING: Be sure that the locking pins have engaged and the legs E are firmly held in place. 3. The locator clip (J) keeps the saw from sliding left or right during cutting operations and during transport. Install the mounting brackets on to the beam as shown by engaging the J concave front lip of the mounting bracket with the rounded front edge of the beam. One of the brackets must engage the locator clip (J). The mounting bracket release levers (E) must be positioned to the rear of the stand as D shown. 4. Measure the distance between the mounting holes of the table saw. E Position the second mounting bracket onto the beam at this distance from the first mounting bracket. 5. Align the holes in the table saw base with the slots in the saw mounting brackets (D). 6. Feed a hex head bolt with flat washer installed through each of the four holes in the table saw base and mounting brackets. Secure each location with a flat washer, lock washer and nut provided. WARNING: To reduce the risk of personal injury, be sure the table saw is fully anchored on the stand. WARNING: The table saw must be positioned on the tool mount so that all four corners can be bolted to the mounting brackets. If the saw is mounted properly, the mounting brackets will be positioned perpendicular to the stand rail when the saw is placed on the stand. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
4
English
Table Saw Bracket Mounting
WARNING: To reduce the risk of injury, turn unit off,
disconnect machine from power source before assembling
the table saw to the table saw stand.
An accidental start-up can
cause injury.
WARNING:
For your own safety, read and understand the
table
saw instruction manual before using. Failure to heed these warnings
may result in personal injury and serious damage to the table saw
and the accessory.
WARNING:
The saw mounting brackets provided with this stand
are equipped with lever locks. To reduce the risk of injury,
DO NOT
modify the mounting bracket lever locks.
1. Unfold the legs by depressing
G
H
F
R
the leg release levers (F).
Rotate the legs until the
locking pin (G) clicks into its
detent (R).
2. Turn the stand upright. The
stand should be stable and
should not rock.
WARNING:
Be sure that
the
locking
pins
have
engaged
and
the
legs
J
E
are firmly held in place.
3. The
locator
clip
(J)
keeps the saw from sliding
left or right during cutting
operations
and
during
transport. Install the mounting
brackets on to the beam as
shown
by
engaging
the
concave front lip of the
mounting bracket with the
E
D
rounded front edge of the
beam. One of the brackets
must engage the locator
clip (J). The mounting
bracket release levers
(E) must be positioned to
the rear of the stand as
shown.
4. Measure the distance
between the mounting
holes of the table saw.
Position
the
second
mounting bracket onto
the beam at this distance
from the first mounting
bracket.
5. Align the holes in the table
saw base with the slots in the
saw mounting brackets (D).
6. Feed a hex head bolt with flat
washer installed through each
of the four holes in the table saw
base and mounting brackets.
Secure each location with a flat
washer, lock washer and nut
provided.
WARNING:
To reduce the risk of personal injury, be sure the table
saw is fully anchored on the stand.
WARNING:
The table saw must be positioned on the tool mount
so that all four corners can be bolted to the mounting brackets. If the
saw is mounted properly, the mounting brackets will be positioned
perpendicular to the stand rail when the saw is placed on the stand.