Dirt Devil UD70183 User Manual - Page 17

Replace - what causes a

Get Dirt Devil UD70183 PDF manuals and user guides View all Dirt Devil UD70183 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

m 0 0 ne CAUTION To reduce the risk of injury from moving parts - Unplug before servicing. REPLACE THE BELT 1. Turn your vacuum over. Use a Phillips screwdriver to take off the 8 screws. Remove the bottom plate. Some models only require 6 screws. 2. Then take off that old belt. Slide on a new belt with the lettering on the outside. 41 4 i- AIM 24*F14.4""-- 1M .4 3. Slip belt around the brushroll in area without bristles (A) and metal pin (B). Each end of the brushroll will fit into pockets on each side of the nozzle (C). Put the plate back on and screw together. MIN I ausao"m' IT l 'FiK4gr.n.-- ■ LUBRICATION: The motor and brushroll are equipped with bearings which contain sufficient lubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brushroll. MENEM u. a. mmeip : NOTE: Any other servicing should be done by an authorized service representative. If appliance is not working as it should, has been dropped, damaged, left outdoors or dropped into water, take it to a service center prior to continuing use. For replacement belt style 5 visit dirtdevil.com or call us at (800) 321-1134. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
m
0
0
REPLACE
THE
BELT
1.
Turn
your
vacuum over.
Use
a
Phillips
screwdriver
to
take
off
the
8
screws.
Remove
the
bottom
plate.
Some
models
only
require
6
screws.
i- AIM
44
1
24
*F14
.4""
--
1M
.4
3.
Slip
belt
around
the
brushroll
in
area
without
bristles
(A)
and
metal
pin
(B).
Each
end
of
the
brushroll
will
fit
into
pockets
on
each
side
of
the
nozzle
(C).
Put
the
plate
back
on
and
screw
together.
MENEM
u.
2.
Then
take
off
that
old
belt.
Slide
on
a
new
belt
with
the
lettering
on
the
outside.
MIN
I
ausao"m'
IT
l
'FiK4gr.n.--
■
LUBRICATION:
The
motor
and
brushroll
are
equipped
with
bearings
which
contain
sufficient
lubrication
for
their
lifetime.
The
addition
of
lubricant
could
cause
damage.
Do
not
add
lubricant
to
motor
or
brushroll.
a.
mmeip
:
NOTE:
Any
other
servicing
should
be
done
by
an
authorized
service
representative.
If
appliance
is
not
working
as
it
should,
has
been
dropped,
damaged,
left
outdoors
or
dropped
into
water,
take
it
to
a
service
center
prior
to
continuing
use.
For
replacement
belt
style
5
visit
dirtdevil.com
or
call
us
at
(800)
321-1134.