EVGA 680i User Guide - Page 27

Connecting Internal Headers - motherboard installation disk

Get EVGA 680i - nForce LT SLI Motherboard PDF manuals and user guides
UPC - 843368000868
View all EVGA 680i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Hardware Installation Connecting Internal Headers Front Panel Header The front panel header on this motherboard is one connector used to connect the following four cables: ‰ PWRLED Attach the front panel power LED cable to these two pins of the connector. The Power LED indicates the system's status. When the system is in S0 status, the LED is on. When the system is in S1, S3, S4, S5 status, the LED is off. No HD_LED Connect RESET - + 9 1 10 2 1 Blank PWRSW - + PWRLED Note: The power LED cable in some chassis is a three pin connector with the pins installed in positions 1 and 3. If your chassis has a three pin connector, you will need to remove pin 3 and put it into position 2 or you can use a pair of scissors to cut out position 2. Most chassis come with a two pin connector. ‰ PWRSW Attach the power button cable from the case to these two pins. Pressing the power button on the front panel turns the system on off rather than using the power supply button. ‰ HD_LED Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator LED indicates the activity status of the hard disks. ‰ RESET Attach the Reset switch cable from the front panel of the case to these two pins. The system restarts when the RESET switch is pressed. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Hardware Installation
19
Connecting Internal Headers
Front Panel Header
The front panel header on this motherboard is one
connector used to connect the following four
cables:
PWRLED
Attach the front panel power LED cable to
these two pins of the connector.
The Power LED indicates the system’s status.
When the system is in S0 status, the LED is
on. When the system is in S1, S3, S4, S5
status, the LED is off.
Note:
The power LED cable in some chassis is a three pin connector
with the pins installed in positions 1 and 3. If your chassis has a
three pin connector, you will need to remove pin 3 and put it into
position 2 or you can use a pair of scissors to cut out position 2.
Most chassis come with a two pin connector.
PWRSW
Attach the power button cable from the case to these two pins. Pressing the
power button on the front panel turns the system on off rather than using the
power supply button.
HD_LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD
indicator LED indicates the activity status of the hard disks.
RESET
Attach the Reset switch cable from the front panel of the case to these two
pins. The system restarts when the
RESET
switch is pressed.
PWRSW
-
+
PWRLED
1
2
1
9
10
HD_LED
RESET
-
+
No
Connect
Blank