Electrolux E30MH65GSS Installation Instructions - Page 20

Install This Microwave Oven

Get Electrolux E30MH65GSS - Icon 1.6 cu. Ft. Convection Microwave Oven PDF manuals and user guides
UPC - 012505558801
View all Electrolux E30MH65GSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installation Instructions 6. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back End A C5. MOUNT THE MICROWAVE OVEN End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 7. Secure the blower unit to the microwave with the screw. Blower-Plate Back of Microwave From the Mounting Plate screw 8. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Adaptor Back of Microwave Guide Guide From Blower motor screw (after attached the exhaust adaptor) Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord. 1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. 2. Rotate front of oven up against cabinet bottom 3. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
Installation Instructions
20
6.
Place the blower unit back into the opening.
CAUTION:
Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should
match exhaust openings on rear of microwave
oven.
7.
Secure the blower unit to the microwave with the
screw.
8.
Attach the exhaust adaptor to the rear of the oven
by sliding it into the guides at the top center of the
back of the oven.
Push in securely until it is in the lower locking tabs.
Take care to assure that the damper hinge is installed
so that it is at the top and that the damper swings
freely.
C5.
MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT
TWO PEOPLE
INSTALL THIS MICROWAVE OVEN
.
IMPORTANT: Do not grip or use handle during
installation.
NOTE:
If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE:
We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
NOTE:
When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
3.
Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least
two full
turns after the
threads have engaged. (It will be completely
tightened later.)
Be sure to keep power cord
tight. Be careful not to pinch the cord,
especially when mounting flush to bottom of
cabinet.
End A
End B
AFTER: Fan Blade
Openings Facing Back
Back of
Microwave
Blower-Plate
From the Mounting
Plate screw
Guide
Back of
Microwave
Adaptor
Guide
From Blower motor screw
(after attached the exhaust adaptor)
2.
Rotate front of oven
up against cabinet
bottom
1.
Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.