Electrolux EI30DS5CJS Installation Instructions (All Languages) - Page 10

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS (Models with an Electric Oven and a Gas Cooktop) 6 LP/Propane Gas Conversion This appliance can be used with Natural gas or LP/ Propane gas. It is shipped from the factory for use with natural gas. If you wish to convert your range for use with LP/ Propane gas, use the supplied fixed orifices located in a bag containing the literature marked "FOR LP/PROPANE GAS CONVERSION." Follow the instructions packaged with the orifices. The conversion must be performed by a qualified service technician in accordance with the manufacturer's instructions and all local codes and requirements. Failure to follow these instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion. Failure to make the appropriate conversion can result in personal injury and property damage. 7 Moving the Appliance for Servicing and Cleaning Turn off the range line fuse or circuit breakers at the main power source, and turn off the manual gas shut-off valve. Make sure the range is cold. Remove the service drawer (warmer drawer on some models) and open the oven door. Lift the range at the front and slide it out of the cut-out opening without creating undue strain on the flexible gas conduit. Make sure not to pinch the flexible gas conduit at the back of the range when replacing the unit into the cut-out opening. Replace the drawer, close the door and switch on the electrical power and gas to the range. 8 Range Installation Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. Refer to the Use and Care Guide for oven door removal instructions. Standard Installation 8.1 The range cooktop overlaps the countertop at the sides and the range rests on the floor. The cooktop is 31½" (80 cm) wide. 8.2 Install base cabinets 30" (76.2 cm) apart. Make sure they are plumb and level before attaching cooktop. Shave raised countertop edge to clear 31½" (80 cm) wide range top rim. 8.3 Install cabinet doors 32" (81.3 cm) min. apart so as not to interfere with range door opening. 8.4 Cutout countertop exactly as shown on page 1. 8.5 Make sure the two front leveling legs and the rear leveling wheels (see page 11) are setup higher than the height of the cabinet (shown on page 3). 8.6 Remove and discard the two rear leveling legs, they are only in place to solidify the unit for the transport. 8.7 Install the anti-tip bracket at this point before placing the range at its final position. Follow the installation instructions on page 14 or on the anti-tip bracket template supplied with the range. 8.8 To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. 8.9 To reduce the risk of damaging your appliance, do not handle or manipulate it by the cooktop. Manipulate with care. 8.10 Position range in front of the cabinet opening. 8.11 Make sure that the underside of the cooktop clears the countertop. If necessary, raise the unit by lowering the front leveling legs and the back leveling wheels. 8.12 Level the range (see section 9). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range". 8.13 Slide the range into the cutout opening. IMPORTANT If Accessories Needed : Installation With Backguard The cutout depth of (21 3/4" (55.2 cm)Min., 22 1/8" (56.2cm) Max.) needs to be increased to 24" (61 cm) when installing a backguard. Installation With End Panel A End Panel kit can be ordered through a Service Center. Installation With Side Panels A Side Panels kit can be ordered through a Service Center. Install cabinet doors 32" (81.3 cm) min. apart so as not to interfere with range door opening. 10