Electrolux EI30EW35KW Product Specifications Sheet (English) - Page 4

Built-In Microwave/Single Wall Oven/Warmer Drawer

Page 4 highlights

30" Combination Installation - Built-In Microwave/Single Wall Oven/Warmer Drawer For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web 24" min. 30" Built-In Microwave Cutout For model: EW30MO55H 21" min. 211/2" max. 2" (visible gap)* 30" Electric Single Wall Oven Cutout For models: EW30EW55G EI30EW35J 27 1/4" min. 27 5/8" max. 30" Warmer Drawer Cutout For model: EW30WD55G 2" min.† 9 7/8" min. 10 1/4" max. 41/2" min. required 27 5/8" min. 28 1/8" max. 28 1/2" min. 28 3/4" max. 28 1/2" min. 28 3/4" max. Full plywood base required to support 100 lbs. 30 1/8" min. 23 5/8" min.** (critical dimension) 120V/60 Hz grounded electrical MUST be located within shaded area Full plywood base required to support 150 lbs. Two 3" wide by 3/4" thick planks must be installed, capable of supporting 200 lbs. Bottom of oven cutout 11 7/8" min.** (critical dimension) * Minimum 2 1/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven's faceplate, leaving a 2" visible gap between both product faceplates. ** Critical dimension - MUST be applied † Maximum height depends on critical dimension (117/8") †† Electrical junction box for Wall Oven must be lower than the Warmer Drawer cutout 3" max.†† Electrical junction box location 4"x 4" opening to route armored cable 30" Combination Installation Specifications • Always consult local and national electric codes. (Refer to product-specific electrical specifications on this page.) • Minimum 23-5/8" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product's faceplate will fit flush against cabinet front. • Bases must be level and cabinet front must be square. • Minimum 4-1/2" required distance from bottom of Warmer Drawer cutout to floor. • Respect critical dimensions as noted for proper installation of built-In products. • Minimum 21" clearance needed for Wall Oven door depth when open. 30" Built-In Microwave Specifications • Product Weight - 82 Lbs. • Voltage Rating - 120V / 60 Hz / 15 Amps • Connected Load (kW Rating) @ 120 Volts = 1.6 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120 Volts = 13.7 Amps • Full oven base of solid plywood or similar material required, capable of supporting 150 Lbs. • Minimum 2-1/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven's faceplate, leaving a 2" visible gap between both product faceplates. 30" Electric Single Wall Oven Specifications • Product Weight - 200 Lbs. • Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line. • Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW • Amps @ 240 / 208 Volts = 17.0 / 14.5 Amps • To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement. 30" Warmer Drawer Specifications • Product Weight - 65 Lbs. • Voltage Rating - 120V / 450W / 60 Hz / 15 Amps • Connected Load (kW Rating) @ 120 Volts = 0.45 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120V = 3.75 Amps • Full base of solid plywood or similar material required, capable of supporting 100 Lbs. Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxappliances.com for detailed instructions. Electrolux Major Appliances, N.A. USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-877-4electrolux (1-877-435-3287) • electroluxappliances.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxappliances.ca MODD_EW_WD 30INST EL 10/10 © 2010 Electrolux Major Appliances, NA High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice. Printed in the U.S.A.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10

30" Combination Installation Specifications
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
Minimum 23-5/8" deep cutout dimension is critical for proper
combination installation, to ensure that each built-in product’s faceplate
will fit flush against cabinet front.
Bases must be level and cabinet front must be square.
Minimum 4-1/2"required distance from bottom of Warmer Drawer cutout
to floor.
Respect critical dimensions as noted for proper installation of built-In
products.
Minimum 21" clearance needed for Wall Oven door depth when open.
30" Built-In Microwave Specifications
Product Weight – 82 Lbs.
Voltage Rating –120V/60Hz/15 Amps
Connected Load (kW Rating) @120 Volts = 1.6kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
Amps @120 Volts =13.7 Amps
Full oven base of solid plywood or similar material required, capable of
supporting 150 Lbs.
Minimum 2-1/8" clearance required from bottom of Built-In Microwave
cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap
between both product faceplates.
30" Electric Single Wall Oven Specifications
Product Weight – 200 Lbs.
Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
Connected Load (kW Rating) @ 240/208 Volts = 4.0/3.0kW
Amps @ 240/208 Volts =17.0/14.5 Amps
To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed
as a base, capable of supporting 200 Lbs. Do NOT use full base, since
planks are necessary to allow for proper air displacement.
30" Warmer Drawer Specifications
Product Weight – 65 Lbs.
Voltage Rating –120V/450W/60Hz/15 Amps
Connected Load (kW Rating) @120 Volts = 0.45kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
Amps @120V = 3.75 Amps
Full base of solid plywood or similar material required, capable of
supporting 100 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxappliances.com for detailed instructions.
30" Combination Installation –
Built-In Microwave/Single Wall Oven/Warmer Drawer
High standards of quality at Electrolux Home Products, Inc. mean
we are constantly working to improve our products. We reserve the right
to change specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
10200 David Taylor Drive
Charlotte, NC 28262
1-877-4electrolux (1-877-435-3287)
electroluxappliances.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
electroluxappliances.ca
MODD_EW_WD 30INST EL
10/10
© 2010 Electrolux Major Appliances, NA
Printed in the U.S.A.
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
24"min.
3"max.
††
30
1
/
8
" min.
9
7
/
8
"min.
10
1
/
4
"max.
2"
min.
Full plywood base
required to support
100 lbs.
27
1
/
4
"min.
27
5
/
8
"max.
28
1
/
2
"min.
28
3
/
4
"max.
Two 3" wide
by
3
/
4
" thick
planks must be
installed, capable
of supporting
200 lbs.
4"x 4" opening to route
armored cable
28
1
/
2
"min.
28
3
/
4
"max.
4
1
/
2
"min.
required
23
5
/
8
"min.**
(critical
dimension)
Electrical junction
box location
Bottom of
oven cutout
11
7
/
8
"min.**
(critical
dimension)
* Minimum 2
1
/
8
"
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2"visible
gap between both
product faceplates.
** Critical dimension –
MUST be applied
Maximum height
depends on critical
dimension (11
7
/
8
")
††
Electrical junction
box for Wall Oven
must be lower than
the Warmer Drawer
cutout
30" Warmer
Drawer Cutout
For model:
EW30WD55G
2"
(visible
gap)*
30" Electric Single
Wall Oven Cutout
For models:
EW30EW55G
EI30EW35J
30" Built-In
Microwave Cutout
For model:
EW30MO55H
21"min.
21
1
/
2
"max.
27
5
/
8
"min.
28
1
/
8
"max.
Full plywood base
required to support
150 lbs.
120V/60Hz
grounded electrical
MUST be located
within shaded area