Electrolux EI30GS55LB Complete Owner's Guide (English) - Page 45

Oven Control Beeps And Displays An F Error Code - reviews

Get Electrolux EI30GS55LB PDF manuals and user guides View all Electrolux EI30GS55LB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Solutions to Common Problems 45 Important Before calling for service, review this list. It may save you both time and expense. This list includes common experiences that are not the result of defective workmanship or material in your cooktop. Oven Control Beeps and Displays an "F" ERROR COde • Electronic control has detected a fault condition. Push CANCEL pad to clear the display and stop the display from beeping. Reprogram the oven. If a fault reoccurs, record the fault number, push the CANCEL pad and contact an authorized servicer. Installation • Place oven rack in center of oven. Place a level on the oven rack. Contact installing agent if rack and cabinet cutout flooring are not level. • Kitchen cabinet misalignment may make range appear to be not level. Be sure cabinets are square and level. Contact cabinet maker to correct problem. Entire range does not operate • When the range is first plugged in, or when the power supply to the oven has been interrupted, the display will flash. The range cannot be programmed until the clock is set. • Be sure electrical cord is securely connected into the electrical junction box. • Cord/plug is not installed and/or connected. Cord is not supplied with range. Contact your dealer, installing agent or authorized servicer. • Service wiring not complete. Contact your dealer, installing agent or authorized servicer. • Power outage. Check house lights to be sure. Call your local electric company. • Short in cord/plug. Replace cord/plug. • Controls are not set properly. See instructions to set the controls. • House fuse has blown or circuit breaker has tripped immediately following installation. • House fuse may not be fully engaged. Check fuse and screw or engage circuit breaker securely. Oven light does not work • Burned-out or loose bulb. Follow the instructions under Oven Light to replace or tighten the bulb. Poor Cooking results • Many factors affect baking results. See Baking for hints, causes and corrections. See Adjusting Oven Temperature. • Many factors affect cooking results. Adjust the recipe's recommended power levels or cooking times. • Cookware is too lightweight or warped. Use heavier quality cookware so foods being prepared may cook more evenly. Self-cleaning cycle does not work • Make sure the oven door is closed. • Make sure you have removed the oven racks and the oven rack supports from the oven. • Controls not set properly. Follow instructions under "Using the Self-Clean Feature".

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
45
Solutions to Common Problems
IMPORTANT
Before calling for service, review this list. It may save you both time and expense. This list
includes common experiences that are not the result of defective workmanship or material
in your cooktop.
OVEN CONTROL BEEPS AND DISPLAYS AN “F” ERROR CODE
•
Electronic control has detected a fault condition. Push
CANCEL pad
to clear the display and stop the display
from beeping. Reprogram the oven. If a fault reoccurs, record the fault number, push the
CANCEL pad
and
contact an authorized servicer.
INSTALLATION
•
Place oven rack in center of oven. Place a level on the oven rack. Contact installing agent if rack and cabinet
cutout flooring are not level.
•
Kitchen cabinet misalignment may make range appear to be not level. Be sure cabinets are square and level.
Contact cabinet maker to correct problem.
ENTIRE RANGE DOES NOT OPERATE
•
When the range is first plugged in, or when the power supply to the oven has been interrupted, the display will
flash. The range cannot be programmed until the clock is set.
•
Be sure electrical cord is securely connected into the electrical junction box.
•
Cord/plug is not installed and/or connected. Cord is not supplied with range. Contact your dealer, installing
agent or authorized servicer.
•
Service wiring not complete. Contact your dealer, installing agent or authorized servicer.
•
Power outage. Check house lights to be sure. Call your local electric company.
•
Short in cord/plug. Replace cord/plug.
•
Controls are not set properly. See instructions to set the controls.
•
House fuse has blown or circuit breaker has tripped immediately following installation.
•
House fuse may not be fully engaged. Check fuse and screw or engage circuit breaker securely.
OVEN LIGHT DOES NOT WORK
•
Burned-out or loose bulb. Follow the instructions under
Oven Light
to replace or tighten the bulb.
POOR COOKING RESULTS
•
Many factors affect baking results. See
Baking
for hints, causes and corrections. See
Adjusting Oven
Temperature.
•
Many factors affect cooking results. Adjust the recipe’s recommended power levels or cooking times.
•
Cookware is too lightweight or warped. Use heavier quality cookware so foods being prepared may cook more
evenly.
SELF-CLEANING CYCLE DOES NOT WORK
•
Make sure the oven door is closed.
•
Make sure you have removed the oven racks and the oven rack supports from the oven.
•
Controls not set properly. Follow instructions under
"
Using the Self-Clean Feature
"
.