Electrolux EIED55HIW Wiring Diagram (All Languages) - Page 1
Electrolux EIED55HIW - 8.0 cu. Ft. Electric Dryer Manual
UPC - 012505378614
View all Electrolux EIED55HIW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Dryer Tech Data Sheet This information is intended for Qualified Technicians Only. CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING Please Return This Sheet to its Envelope in the Product for Future Reference Contents Page Error code explanation 1 Error Code Chart 1-2 Diagnostics 3 Français 4-6 Español 7-9 Wiring Diagram 10-11 Acronym Table CW - Clockwise CCW - Counter Clockwise READING ERROR CODES 1. Wake the dryer up by pressing any button but "cancel". 2. Press and hold the "cancel" and "start pause" buttons simultaneously for 6 seconds to show the last error code recorded. The error code will appear in the display as an E followed by two numbers. NOTE: E00 means no failure code experienced. 3. To view the last 5 error codes recorded, refer to the Diagnostic Mode listed below. 4. Troubleshoot problem by using the chart below. Error Code Fault E31 Contact Sensor frequency too high E32 Contact Sensor frequency too low E42 Door Sensing failure Possible Fault Conditions Electronic Control Board defective or foreign object interfering with contact sensor Electronic Control Board defective or foreign object interfering with contact sensor Electronic Control Board defective Possible Solutions Check Contact Sensor and wiring. If no problems are found with Contact Sensor, replace Electronic Control Board. Check Contact Sensor and wiring. If no problems are found with Contact Sensor, replace Electronic Control Board. Replace Electronic Control Board. If motor runs continuously with power applied check for short circuit across E51 Motor Relay failure Motor Relay stuck open or closed; motor relay (RL2), or L1 applied to motor relay output (J3-1) with cycle Wiring defective stopped. If motor does not start when "start" key is pressed, check for open circuit between L1 and motor relay connection (J3-2). If no wiring problems found, replace Electronic Control Board. Motor Fault - Motor overheating; Laundry load too Remove any load from dryer and check if drum turns freely by hand. Check E52 motor stopped or heavy; Low power supply; Motor, or L1 power supply voltage, motor wiring, and motor thermal protector (if motor not starting Wiring defective thermal protector has tripped, it may take up to 30 minutes to reset). Motor Centripetal E53 Switch Failure Motor Centripetal Switch, Electronic Check wiring. Check if Motor Centripetal Switches are stuck in open or closed Control Board Defective, or wiring positions. Replace motor. Replace Electronic Control Board. defective. E54 Motor Sensing failure E61 Heater Relay failure Electronic Control Board defective Heater relay stuck open or closed; Wiring defective Replace Electronic Control Board and retest. Check for short circuit across heater relay(s) (RL5, RL6, RL7) or L1 applied to heater relay output(s) (J5-2, J7-1, J7-3) with cycle stopped. Check for open circuit between L1 and heater relay connection(s) (J5-1, J5-3, J7-2). If no wiring problems are found, replace Electronic Control Board and retest. E63 Heater to Earth Ground Check heater coils and connections for short circuits to the cabinet. Replace Heating element or wiring defective heater and/or wiring and retest. E64 Heater Open Circuit Check heater coils and connections for open circuits. Replace heater and/or Heating element or wiring defective wiring and retest. For Electric Model, check Inlet Thermal Limiter for continuity. If Thermal Limiter High Limit High vent restriction, High Limit is open, check for evidence of high temperature event and any resulting E65 Thermostat trip count too high Thermostat defective or Inlet Thermal damage. If no further damage is evident, replace Thermal Limiter. If no Limiter tripped (Electric Model only) problems are found with the Thermal Limiter, check exhaust vent system for air blockages. If no problems with vent restrictions, check/replace High Limit Thermostat, and retest. E66 Thermal Limiter Open Circuit Outlet Thermal Limiter tripped Inlet Thermal Limiter tripped (Gas Model only) or wiring defective Check Outlet Thermal Limiter for continuity. For Gas Model, also check Inlet Thermal Limiter for continuity. If Thermal Limiter is open, check for evidence of high temperature event and any resulting damage. If no further damage is evident, replace Thermal Limiter and retest. E67 Heaters Sensing Failure Electronic Control Board defective Replace Electronic Control Board and retest. 1 137032700B (0209)