Electrolux EIED55HIW Wiring Diagram (All Languages) - Page 3

cancel, far left button under the, display - heater

Page 3 highlights

Selector Position 0 Test/Activated Component Electric Gas Lights / Buttons test 1 Motor Clockwise (CW) 2 Contact Sensor Diagnostic Mode Operator Check LCD row Check Motor function. Look for Drum rotation in clockwise direction "MOTOR CW" Check moisture reading. Place fingers across Contact Sensor and look for digit display to change from "1111" to "8888" "MOIST. BARS" 3 Motor Clockwise (CW) Check Motor function. Look for Drum rotation in clockwise direction "MOTOR CW" 4 Lights / Buttons test + Motor CW Lights / Buttons test + Motor CW + igniter Check all buttons and lights. Press all buttons and check for beep and button ID number in digit display. Check to see that all Lights function 5 Motor CW + Heater 1 Motor CW + Heater Check Motor and Heater function. Check Outlet Control Thermistor value in digit display. "HEAT1 - NTC1" 6 Motor CW + Heater 1 + Heater 2 Motor CW + Heater Check Motor and Heater function. Check Inlet Control Thermistor value in digit display. "HEAT2 - NTC2" 7 Motor CW + Heater 1 + Heater 2 + Heater 3 Motor CW + Heater Check Motor and Heater function. Check Outlet Control Thermistor value in digit "HEAT3 - NTC1" display. 8 Motor Clockwise (CW) "MOTOR CW" 9 Error code history display Check last 5 error codes displayed (See Table above for error code definitions) 10 Software version Software version Software version LCD digits "1111" if Contact Sensor open circuit;"8888" if Contact Sensor short circuited button id number Outlet Control Thermistor value (degrees F) Inlet Control Thermistor value (degrees F) Outlet Control Thermistor value (degrees F) error code Software version NOTE : To clear the error code (s): Press and hold the far left key under the display and "cancel" buttons simultaneously for 3 seconds. 6. To exit Diagnostic Mode: a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR b) Turn the program knob to the Start Position (lights/Buttons Test). Press the "cancel" and far left button under the display simultaneously for 6 seconds. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12

3
Diagnostic Mode
Selector
Test/Activated Component
Operator Check
LCD row
LCD digits
Position
Electric
Gas
NOTE :
To clear the error code (s): Press and hold the
far left key under the display
and “
cancel”
buttons
simultaneously for 3 seconds.
6.
To exit Diagnostic Mode:
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob to the
S
t
art Position (light
s/Buttons
T
est). Press the “
cancel
” and
far left button under the
display
simultaneously for 6 seconds.
0
1
2
3
4
5
6
7
8
9
10
Lights / Buttons test
Motor
Clockwise (CW)
Contact Sensor
Motor Clockwise (CW)
Lights / Buttons
test + Motor CW
Motor CW + Heater
1
Motor CW + Heater
1 + Heater 2
Motor CW + Heater
1 + Heater 2 +
Heater 3
Lights / Buttons
test + Motor CW +
igniter
Motor CW +
Heater
Motor CW +
Heater
Motor CW +
Heater
Motor Clockwise (CW)
Error code history display
Software version
Check Motor function. Look for Drum
rotation i
n clockwise direction
Check moisture reading. Place fingers
across Contact Sensor and look for digit
display to change from “1111” to “8888”
Check Motor function. Look for Drum
rotation in clockwise direction
Check all buttons and lights. Press all
buttons and check for beep and button
ID number in digit display. Check to see
that all Lights function
Check Motor and Heater function. Check
Outlet Control Thermistor value in digit
display.
Check Motor and Heater function. Check
Inlet Control Thermistor value in digit
display.
Check Motor and Heater function. Check
Outlet Control Thermistor value in digit
display.
Check last 5 error codes displayed (See
Table above for error code definitions)
Software version
“MOTOR CW”
“MOIST. BARS”
“MOTOR CW”
“HEAT1 - NTC1”
“HEAT2 - NTC2”
“HEAT3 - NTC1”
“MOTOR CW”
Software
version
“1111” if Contact Sensor
open circuit;”8888" if
Contact Sensor short
circuited
button id number
Outlet Control Thermistor
value (degrees F)
Inlet Control Thermistor
value (degrees F)
Outlet Control Thermistor
value (degrees F)
error code
Software version