Electrolux ELFI18K7MB Complete Owner's Guide (English) - Page 8
Solución de problemas, Troubleshooting, Gestion des pannes
![]() |
View all Electrolux ELFI18K7MB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Troubleshooting Solución de problemas EN Problem Soleplate is not heating even though iron is turned on. Iron does not produce steam. Possible cause Connection problem Temperature control is in MIN position. Not enough water in tank. Steam control is selected in non-steam position. Spray function does not work. Steam jet and vertical steam jet function does not work. Not enough water in tank. Steam jet function was used very frequently within a short period. Iron is not hot enough. Water leaks from the soleplate during ironing. The iron is not hot enough. Flakes and impurities come out of the soleplate during ironing. Water leaks from the soleplate while the iron is cooling down or after it has been stored. You have used hard water, which has caused scale flakes to develop in the water tank. The iron has been put in horizontal position while there is still water in the water tank. Solution Check main power supply cable, plug and outlet. Select adequate temperature. Fill water tank (see "Getting started", no 2). Set steam control between positions of minimum steam and maximum steam (see "Ironing chart"). Fill water tank (see "Getting started", no 2). Put iron on horizontal position and wait before using steam jet function. Adjust the proper temperature to steam ironing (up to ). Put iron in vertical position and wait until temperature indicator light turns off. Set the temperature dial to a temperature ( to maximum) suitable for steam ironing. Put the iron on its heel and wait until the light has gone out before you start ironing. Use the self-clean function one or more times. Empty the water tank and set the steam control to position off before storing the iron. Gestion des pannes FR Problème Cause possible La semelle ne chauffe pas alors que le fer est Problème de raccordement allumé. Solution Vérifiez le cordon d'alimentation, la fiche et la prise. Le contrôle de température est sur la position MIN. Choisissez la température adéquate. Le fer ne produit pas de vapeur. Manque d'eau dans le réservoir. Remplir le réservoir (voir « Première utilisation », n° 2). Le contrôleur de vapeur est sur la position sans vapeur. Placez le contrôleur de vapeur entre les positions minimum de vapeur et maximum de vapeur (voir le « Tableau de repassage »). La température choisie est inférieure à celle spécifiée pour une utilisation avec vapeur. Choisissez une température jusqu'à . La fonction brumisateur ne fonctionne pas. Manque d'eau dans le réservoir. Remplir le réservoir (voir « Première utilisation », n° 2). Les fonctions jet de vapeur et jet de vapeur vertical ne fonctionnent pas. La fonction jet de vapeur a été très utilisée sur une courte période. Placez le fer en position horizontale et patientez avant d'utiliser la fonction jet de vapeur. Le fer n'est pas suffisament chaud. Réglez la température convenablement pour un repassage à la vapeur (jusqu'à ). Placez le fer en position verticale et patientez jusqu'à ce que voyant indicateur de température s'éteigne. ES Problema La plancha no se calienta a pesar de que la plancha está encendida. Posible causa Problema de conexión Solución Compruebe el cable y el enchufe de alimentación eléctrica, así como la toma de red. El ajuste de temperatura se encuentra en la posición MIN. Seleccione la temperatura adecuada. La plancha no genera vapor. No hay suficiente agua en el depósito. Cargue el depósito de agua (consulte el segundo epígrafe de "Introducción"). El mando de vapor está situado en una posición no de vapor. Sitúe el mando de vapor entre las posiciones de mínimo y máximo (consulte "Tabla de temperaturas de planchado"). La temperatura seleccionada es inferior a la especificada para utilizar el vapor. Seleccione una temperatura de hasta . La función de pulverización no funciona. No hay suficiente agua en el depósito. Cargue el depósito de agua (consulte el segundo epígrafe de "Introducción"). Las funciones de chorro de vapor y chorro de vapor vertical no funcionan. Se está utilizando la función de chorro de vapor con demasiada frecuencia en un período corto. Coloque la plancha en posición horizontal y espere unos instantes antes de utilizar la función de chorro de vapor. La plancha no está lo bastante caliente. Ajuste la temperatura adecuada para el planchado a vapor (hasta ). Coloque la plancha en posición vertical y espere a que el indicador luminoso de temperatura se apague. 14 15
![](/manual_guide/products/electrolux-elfi18k7mb-complete-owners-guide-english-204d83f/8.png)