Electrolux EW30GS65GS Complete Owner's Guide (English) - Page 18

Setting Surface Controls - manual

Get Electrolux EW30GS65GS - 30inch Slide-In Gas Range PDF manuals and user guides
UPC - 057112096995
View all Electrolux EW30GS65GS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

18 Setting Surface Controls setting surface controls Your cooktop may be equipped with any combination of the following burners: Simmer Burner: best used for simmering delicate sauces, etc. Standard Burner: used for most all surface cooking needs. Large Burner: best used when bringing large quantities of liquid to temperature and when preparing larger quantities of food. Regardless of size, always select a utensil that is suitable for the amount and type of food being prepared. Select a burner and flame size appropriate to the pan. Never allow flames to extend beyond the outer edge of the pan. Your cooktop is also equipped with 270° rotation flame control valves. These valves provide enhanced control of the burner flame. Each burner lights automatically from an electric ignitor when its control knob is turned to the LITE position. ! Caution Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top of the cooktop when it is in use. These items could melt or ignite. Potholders, towels or wood spoons could catch fire if placed too close to a flame. OFF To operate the surface burner: 1. Place cooking utensil on burner. 2. Push in and turn the Surface Control knob to (LITE). Note: All electronic ignitors will click at the same time. However, only the burner you are turning on will ignite. 3. Visually check that the burner has lit. 4. Turn the control knob to the desired flame size. The control knobs do not have to be set at a particular mark. Use the guides and adjust the flame as needed. DO NOT cook with the Surface Control knob in the position. (The electronic ignitor will continue to click if left in the position, causing premature wear.) In the event of an electrical power outage, the surface burners can be lit manually. To light a surface burner, hold a lit match to the burner head, then slowly turn the Surface Control knob to . Use caution when lighting surface burners manually.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
18
Setting Surface Controls
SETTING SURFACE CONTROLS
Your cooktop may be equipped with any combination of the following burners:
Simmer Burner: best used for simmering delicate sauces, etc.
Standard Burner: used for most all surface cooking needs.
Large Burner: best used when bringing large quantities of liquid to temperature and when
preparing larger quantities of food.
Regardless of size, always select a utensil that is suitable for the amount and type of food
being prepared. Select a burner and flame size appropriate to the pan. Never allow flames
to extend beyond the outer edge of the pan.
Your cooktop is also equipped with 270° rotation flame control valves. These valves provide
enhanced control of the burner flame. Each burner lights automatically from an electric ignitor
when its control knob is turned to the
LITE
position.
!
CAUTION
Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top
of the cooktop when it is in use.
These items could melt or ignite. Potholders, towels or wood spoons could
catch fire if placed too close to a flame.
OFF
To operate the surface burner:
1. Place cooking utensil on burner.
2.
Push in and turn
the Surface Control knob to
(LITE)
.
Note:
All
electronic ignitors will click at the same time. However, only the burner
you are turning on will ignite.
3. Visually check that the burner has lit.
4.
Turn
the control knob to the desired flame size. The control knobs do
not have to be set at a particular mark. Use the guides and adjust the
flame as needed.
DO NOT
cook with the Surface Control knob in the
position. (The electronic ignitor will continue to click if left in the
position, causing premature wear.)
In the event of an electrical power outage, the surface burners can be lit
manually. To light a surface burner, hold a lit match to the burner head,
then slowly turn the Surface Control knob to
. Use caution when lighting
surface burners manually.