Emerson CF152 Owner Manual - Page 8

How to Wire Your Ceiling Fan, How to Assemble Your Light Kit Glass Shade

Page 8 highlights

How to Wire Your Ceiling Fan (continued) 3. After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other inside of the outlet box. 4. Remove one of the four screws in the ceiling mounting plate and loosen the remaining three screws (Figure 11). 5. Unhook the fan motor housing from the ceiling mounting plate hook and lift the fan motor housing assembly up to the ceiling mounting plate. Align and engage the motor assembly slots with the three screw heads previously loosened by rotating the fan motor housing assembly to engage the screw heads and all three slots. Install the previously removed M5 x 10mm screw and secure the assembly to the plate (Figure 11). Completely tighten all four screws. CEILING MOUNTING PLATE M5 x 10mm PAN HEAD CEILING COVER SCREWS Figure 11 FAN MOTOR HOUSING ASSEMBLY CEILING COVER SCREW HEADS (4) ! WARNING To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling mounting plate and the fan motor housing assembly. 6. Position the ceiling trim ring over each of the protruding ceiling cover screw heads and rotate the ceiling trim ring clockwise to secure (Figure 12). Figure 12 CEILING TRIM RING FAN MOTOR HOUSING ASSEMBLY How to Assemble Your Light Kit Glass Shade 1. Screw in two 50-watt (maximum) halogen mini candelabra base bulbs in the light kit plate sockets (Figure 13). 2. Place the glass shade into the opening in the fan motor housing assembly, aligning the three flat areas on the top edge of the glass with the three raised dimples on the fan motor housing assembly and turn the glass shade clockwise until it stops (Figure 14). NOTE: periodically check that the glass shade is seated fully clockwise in the fan motor housing assembly. DIMPLES (3) 50-WATT (maximum) HALOGEN MINI CANDELABRA BASE BULBS (2) Figure 13 LIGHT KIT PLATE SOCKETS (2) FLAT AREA (3) Figure 14 GLASS BOWL 8 U.L. Model No.: CF144 & CF152

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

8
U.L. Model No.: CF144 & CF152
3.
After connections have been made, turn leads
upward and carefully push leads into the outlet box,
with the white and green leads on one side of the
outlet box and the black and blue leads on the other
inside of the outlet box.
4.
Remove one of the four screws in the ceiling
mounting plate and loosen the remaining three
screws (Figure 11).
5.
Unhook the fan motor housing from the ceiling
mounting plate hook and lift the fan motor housing
assembly up to the ceiling mounting plate. Align and
engage the motor assembly slots with the three
screw heads previously loosened by rotating the fan
motor housing assembly to engage the screw heads
and all three slots. Install the previously removed M5
x 10mm screw and secure the assembly to the plate
(Figure 11). Completely tighten all four screws.
6.
Position the ceiling trim ring over each of the
protruding ceiling cover screw heads and rotate the
ceiling trim ring clockwise to secure (Figure 12).
1.
Screw in two 50-watt (maximum) halogen mini
candelabra base bulbs in the light kit plate sockets
(Figure 13).
2.
Place the glass shade into the opening in the fan
motor housing assembly, aligning the three flat areas
on the top edge of the glass with the three raised
dimples on the fan motor housing assembly and turn
the glass shade clockwise until it stops
(Figure 14).
NOTE: periodically check that the glass shade is
seated fully clockwise in the fan motor housing
assembly.
How to Wire Your Ceiling Fan
(continued)
How to Assemble Your Light Kit Glass Shade
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling mounting plate
and the fan motor housing assembly.
WARNING
!
FAN MOTOR
HOUSING
ASSEMBLY
CEILING MOUNTING
PLATE
M5 x 10mm PAN HEAD
CEILING COVER SCREWS
Figure 11
FAN MOTOR
HOUSING
ASSEMBLY
CEILING TRIM
RING
CEILING COVER SCREW
HEADS (4)
Figure 12
50-WATT (maximum)
HALOGEN MINI CANDELABRA
BASE BULBS (2)
LIGHT KIT PLATE
SOCKETS (2)
Figure 13
DIMPLES (3)
FLAT AREA (3)
GLASS
BOWL
Figure 14