Epic Fitness 400 Mx User Manual - Page 6

Assembly

Get Epic Fitness 400 Mx PDF manuals and user guides View all Epic Fitness 400 Mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrench and adjustable wrench . and your own Phillips screwdriver For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags, check to see if the part has been preattached. Wheel Bolt (92)-2 Console Bolt (86)-4 1" Tek Screw (98)-4 Nut (25)-2 Star Washer (88)-4 1. With the help of a second person, carefully raise the Uprights (99) to the position shown. Have the second person hold the console assembly near the Uprights as shown. Look under the console assembly and locate the Console Wire Harness (22). 1 Console Assembly Cut the plastic ties securing the Upright Wire Harness (108) to the right Upright (99). Connect the Upright Wire Harness to the Console Wire Harness (22). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 22 108 22 99 108 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
ASSEMBLY
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrench
and your own Phillips screwdriver
and adjustable wrench
.
For help identifying assembly hardware, see the drawings below.
Note: If a part is not found in the part bags,
check to see if the part has been preattached.
6
1” Tek Screw (98)–4
Nut (25)–2
Star Washer (88)–4
Console Bolt (86)–4
Wheel Bolt (92)–2
1.
With the help of a second person, carefully raise the
Uprights (99) to the position shown. Have the second per-
son hold the console assembly near the Uprights as
shown. Look under the console assembly and locate the
Console Wire Harness (22).
Cut the plastic ties securing the Upright Wire Harness
(108) to the right Upright (99). Connect the Upright Wire
Harness to the Console Wire Harness (22).
Make sure to
connect the connectors properly (see the inset draw-
ing). The connectors should slide together easily and
snap into place.
If the connectors do not slide together
easily and snap into place, turn one connector and try
again.
IF THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED
WHEN THE POWER IS TURNED ON.
99
108
22
1
Console
Assembly
108
22