Epson 1776W EasyMP Network Projection - Operations Guide - Page 42

Cannot select or change the connection mode., cannot be made from another computer.

Get Epson 1776W PDF manuals and user guides View all Epson 1776W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Troubleshooting 42 Check Remedy Are the access point and the projector's subnet different? Select Manual search from EasyMP Network Projection, specify the IP address, and connect. (Advanced Connection Mode only) Have you enabled DHCP? (Advanced Connection Mode When DHCP is set to On in Advanced Connection Mode, it may take some time to enter LAN standby only) status if an available DHCP server is not found. When a connection is made using EasyMP Network Projection, the projected image remains as it is, and a connection cannot be made from another computer. Check Did the presenter leave the conference room without cutting off the network connection? Remedy With EasyMP Network Projection, the computer currently connected can be disconnected when another computer tries to connect to the projector. Therefore, when a Projector Keyword is not set for the projector, or if you know the Projector Keyword, you can disconnect the computer currently connected and then connect your computer to the projector. When a Projector Keyword is set for the projector and you do not know the Projector Keyword, restart the projector and reconnect. Cannot select or change the connection mode. Check Is EasyMP Network Projection set to start up using the same connection mode? Remedy Select Display Connection Mode Selection window on startup on the General settings tab from Set options. The projector selection screen is displayed after restarting EasyMP Network Projection.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
Troubleshooting
42
When a connection is made using EasyMP Network Projection, the projected image remains as it is, and a connection
cannot be made from another computer.
Cannot select or change the connection mode.
Are the access point and the projector's subnet different?
(Advanced Connection Mode only)
Select
Manual search
from EasyMP Network Projection, specify the IP address, and connect.
Have you enabled DHCP? (Advanced Connection Mode
only)
When DHCP is set to
On
in Advanced Connection Mode, it may take some time to enter LAN standby
status if an available DHCP server is not found.
Check
Remedy
Did the presenter leave the conference room without
cutting off the network connection?
With EasyMP Network Projection, the computer currently connected can be disconnected when
another computer tries to connect to the projector.
Therefore, when a Projector Keyword is not set for the projector, or if you know the Projector
Keyword, you can disconnect the computer currently connected and then connect your computer to
the projector.
When a Projector Keyword is set for the projector and you do not know the Projector Keyword, restart
the projector and reconnect.
Check
Remedy
Is EasyMP Network Projection set to start up using the
same connection mode?
Select
Display Connection Mode Selection window on startup
on the
General settings
tab from
Set options
. The projector selection screen is displayed after restarting EasyMP Network Projection.
Check
Remedy