Epson FX 890 Service Manual - Page 57

Upper Housing Removal - paper release lever

Get Epson FX 890 - B/W Dot-matrix Printer PDF manuals and user guides
UPC - 010343846746
View all Epson FX 890 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

FX-1180/FX-880 Service Manual Chapter 4 DISASSEMBLY AND ASSEMBLY 4.2.4 Upper Housing Removal 1. Remove the PAPER GUIDE ASSEMBLY, top cover, front cover, paper eject cover, knob and tractor unit. (See Section 4.2.3.) 2. Remove 2 CBS (M3 × 6) screws and a CBB (4 × 12) screw securing the upper housing to the lower case. 3. Set the release lever to the friction feed side. 4. Opening the front side of the upper housing a little, disconnect the Panel FFC from the connector in the panel assembly. 5. Opening the front side of the upper housing a little, release 2 hooks securing the panel assembly to the upper housing at the front bottom side of the upper housing. Then remove the panel. 6. Open the upper housing from the front side, and remove it . P anelF F C P a n e l A s s e m b ly C B B (4 x 1 2 ) S H E E T ,R E L A S E ,C A P C B S (M 3 x 6 ) U p p e r H o u s in g C B S (M 3 x 6 ) R e le a s e L e v e r Low er C ase P anelF F C Figure 4-5. Upper Housing Removal CAUTION T When assembling the upper housing, put the hooks in the upper housing on the catching holes at the rear side of the lower case at first, then close the housing. T Mount the Panel assembly onto the upper housing before installing the upper housing assembly. T Sheet, Release, Cap can be assembled after the upper housing assembly is installed. Rev. B 4-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
FX-1180/FX-880 Service Manual
Chapter 4 DISASSEMBLY AND ASSEMBLY
Rev. B
4-8
4.2.4 Upper Housing Removal
1.
Remove the PAPER GUIDE ASSEMBLY, top cover, front cover, paper eject cover, knob and
tractor unit. (See Section 4.2.3.)
2.
Remove 2 CBS (M3
×
6) screws and a CBB (4
×
12) screw securing the upper housing to the
lower case.
3.
Set the release lever to the friction feed side.
4.
Opening the front side of the upper housing a little, disconnect the Panel FFC from the
connector in the panel assembly.
5.
Opening the front side of the upper housing a little, release 2 hooks securing the panel
assembly to the upper housing at the front bottom side of the upper housing. Then remove
the panel.
6.
Open the upper housing from the front side, and remove it .
U
p p e r H
o u s in g
R
e le a s e L e v e r
S
H
E
E
T ,R
E
LA
S
E
,C
A
P
C
B
B
( 4 x 1 2 )
C
B
S
(M
3 x 6 )
P
a n e l A
ssem
b ly
Low
e r C
ase
P
a n e l F F C
P
a n e l F F C
C
B
S
(M
3 x 6 )
Figure 4-5. Upper Housing Removal
CAUTION
When assembling the upper housing, put the hooks in the upper
housing on the catching holes at the rear side of the lower case at
first, then close the housing.
Mount the Panel assembly onto the upper housing before installing
the upper housing assembly.
Sheet, Release, Cap can be assembled after the upper housing
assembly is installed.