Epson H6000IIP User Manual - Page 61

TM USB Driver should refer to EPSON TM USB Driver of this, and ElectronicJournal - printer drivers

Get Epson H6000IIP - TM Two-color Thermal Line PDF manuals and user guides View all Epson H6000IIP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Version 2.65 Jul. 2009 the actual files do not exist. • If the installation fails for some reason, or it is canceled during the execution, be sure to perform a reinstallation. In the condition where installation has failed or been canceled, the settings, etc. may not be completely removed even if uninstallation is performed. EPSON OPOS ADK may malfunction due to the failure of the first installation even after the reinstallation. It is recommended to uninstall EPSON OPS ADK and install it again. • When using USB POSPrinter, MICR, LineDisplay, CheckScanner, CashDrawer and ElectronicJournal, install the Epson TM USB Driver (Epson USB controller for TM printer series) in advance. It is not possible to install the USB OPOS information unless the Epson TM USB driver is installed. Users of the EPSON TM USB Driver should refer to "Section 6. EPSON TM USB Driver" of this manual. • When Version 1.xx and Version 2.xx are installed coexisting, the operation of Version 2.xx will not be normal if the uninstaller of Version 1.xx is used. Be sure to uninstall Version 2.xx first, or use the uninstaller of Version 2.xx to uninstall Version 1.xx. • If Version 2.xx is uninstalled under the coexisting environment of Version 1.xx and Version 2.xx, the subsequent behavior of Version 1 is not guaranteed. In such a case reinstall Version 1.xx and make the prescribed settings. • You can install and uninstall CCO using the SetupPOS utility; subsequently, however, the CCO registration information and the Installer cannot be synchronized. When CCO is registered by the SetupPOS utility while CCO is not installed by the Installer, or when CCO is released by the SetupPOS utility while CCO is installed by the Installer, the Installer message may not be appropriate. • When overwriting Version 1.xx by Version 2.xx, the settings of the trace function on Version 1.xx may not be succeeded. They are as follows. CashDrawer: "Open Status Phase" (Device Specific Settings) POSPrinter: "Reverse feed removal" (Device Specific Settings) All devices: When the Trace file name is setting to default value by the OPOS API Trace Setting. Set the trace function again before using it after the information was succeeded. When overwriting Version 1.xx by Version 2.xx in the above cases, please redefine the setting by the SetupPOS Utility after installing. If both Version 1.xx and Version 2.xx exist at the same time and "Trace All" is selected for each version, only trace of either one of the versions can be taken. • When the reboot setting after the Silent Installation is being specified, the system reboots automatically after the installation. The data being edited 56 User's Manual Installer, SetupPOS, TMUSB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Version 2.65
Jul. 2009
56
User's Manual
Installer, SetupPOS, TMUSB
the actual files do not exist.
•
If the installation fails for some reason, or it is canceled during the execution,
be sure to perform a reinstallation. In the condition where installation has failed
or been canceled, the settings, etc. may not be completely removed even if
uninstallation is performed. EPSON OPOS ADK may malfunction due to the
failure of the first installation even after the reinstallation. It is recommended to
uninstall EPSON OPS ADK and install it again.
•
When using USB POSPrinter, MICR, LineDisplay, CheckScanner, CashDrawer
and ElectronicJournal, install the Epson TM USB Driver (Epson USB controller
for TM printer series) in advance. It is not possible to install the USB OPOS
information unless the Epson TM USB driver is installed. Users of the EPSON
TM USB Driver should refer to "Section 6. EPSON TM USB Driver" of this
manual.
•
When Version 1.xx and Version 2.xx are installed coexisting, the operation of
Version 2.xx will not be normal if the uninstaller of Version 1.xx is used. Be sure
to uninstall Version 2.xx first, or use the uninstaller of Version 2.xx to uninstall
Version 1.xx.
•
If Version 2.xx is uninstalled under the coexisting environment of Version 1.xx
and Version 2.xx, the subsequent behavior of Version 1 is not guaranteed.
In
such a case reinstall Version 1.xx and make the prescribed settings.
•
You can install and uninstall CCO using the SetupPOS utility; subsequently,
however, the CCO registration information and the Installer cannot be
synchronized.
When CCO is registered by the SetupPOS utility while CCO is not installed by
the Installer, or when CCO is released by the SetupPOS utility while CCO is
installed by the Installer, the Installer message may not be appropriate.
•
When overwriting Version 1.xx by Version 2.xx, the settings of the trace
function on Version 1.xx may not be succeeded. They are as follows.
CashDrawer:
“Open Status Phase” (Device Specific Settings)
POSPrinter:
“Reverse feed removal” (Device Specific Settings)
All devices:
When the Trace file name is setting to default value by the
OPOS API Trace Setting.
Set the trace function again before using it after the information was succeeded.
When overwriting Version 1.xx by Version 2.xx in the above cases, please
redefine the setting by the SetupPOS Utility after installing.
If both Version 1.xx and Version 2.xx exist at the same time and "Trace All" is
selected for each version, only trace of either one of the versions can be taken.
•
When the reboot setting after the Silent Installation is being specified, the
system reboots automatically after the installation. The data being edited