Epson NX Product Support Bulletin(s) - Page 1

Epson NX Manual

Get Epson NX PDF manuals and user guides View all Epson NX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Product Support Bulletin EPSON Subject: Epson NX Multimedia PC, CDR101 ERROR Date: 05/18/94 Page(s): 1 of 1 PSB No: S-0176 Originator: RWS This bulletin provides updated reinstallation information of the Multimedia software from the "Media Vision Spectrum 16 Drivers for DOS and Windows" installation disk. The product codes affected are: A432360, A432361, A432370, A432371. PROBLEM: CDR101 errors are exhibited when the CD ROM drive is accessed after the reinstallation of the Media Vision software. The CDR101 errors are due to an OLD version (3.06) of TSLCDR.SYS (34,239 dated 7-15-93) being installed to the hard drive. This file is in compressed form on the installation disk and therefore is not listed if a directory command is performed on the installation disk. SOLUTION: Copy the NEW version (3.12) of TSLCDR.SYS (34,975 dated 12-01-93) Included in the root directory of the Media Vision INSTALLATION disk, to the C:\SPECTRUM directory on the hard drive. Then RE-BOOT the PC. To copy the NEW version of the TSLCDR.SYS file to your hard drive insert the Media Vision installation diskette into the floppy drive A:, go to a DOS prompt C:\>, and type in the copy command listed below, followed by pressing the ENTER key. C:\>COPY A:\TSLCDR.SYS C:\SPECTRUM NOTE: Copy the NEW TSLCDR.SYS file to your hard drive each time the Media Vision installation diskette is used to reinstall the multimedia software. VERIFICATION: 1. Re-boot your EPSON NX Multimedia PC by turning it OFF and then back ON. 2. Insert a CD ROM program disk into the CD ROM drive. 3. Go to the DOS prompt C:\> 4. Change to the CDROM drive by typing a D:, C:\>D: followed by the ENTER key. 5. Do a directory command by typing DIR, D:\>DIR followed by the ENTER key, 6. You should see a listing of the contents of the CD installed.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
EPSON
Product Support Bulletin
Subject: Epson NX Multimedia PC, CDR101 ERROR
Date: 05/18/94
PSB No: S-0176
Page(s): 1 of 1
Originator: RWS
This bulletin provides updated reinstallation information of the Multimedia software
from the “Media Vision Spectrum 16 Drivers for DOS and Windows” installation
disk. The product codes affected are: A432360, A432361, A432370, A432371.
PROBLEM:
CDR101 errors are exhibited when the CD ROM drive is accessed after the
reinstallation of the Media Vision software. The CDR101 errors are due to an OLD
version (3.06) of TSLCDR.SYS (34,239 dated 7-15-93) being installed to the hard
drive. This file is in compressed form on the installation disk and therefore is not
listed if a directory command is performed on the installation disk.
SOLUTION:
Copy the NEW version (3.12) of TSLCDR.SYS (34,975 dated 12-01-93) Included in
the root directory of the Media Vision INSTALLATION disk, to the C:\SPECTRUM
directory on the hard drive. Then RE-BOOT the PC.
To copy the NEW version of the TSLCDR.SYS file to your hard drive insert the
Media Vision installation diskette into the floppy drive
A:,
go to a DOS prompt C:\>,
and type in the copy command listed below, followed by pressing the
ENTER
key.
C:\>COPY A:\TSLCDR.SYS C:\SPECTRUM
NOTE: Copy the NEW TSLCDR.SYS file to your hard drive each time the Media
Vision installation diskette is used to reinstall the multimedia software.
VERIFICATION:
1. Re-boot your EPSON NX Multimedia PC by turning it OFF and then back ON.
2. Insert a CD ROM program disk into the CD ROM drive.
3. Go to the DOS prompt C:\>
4. Change to the CDROM drive by typing a
D:, C:\>D:
followed by the
ENTER
key.
5. Do a directory command by typing DIR,
D:\>DIR
followed by the
ENTER
key,
6. You should see a listing of the contents of the CD installed.