Epson PowerLite 480 Quick Setup - Page 3

Project over a wirednetwork

Get Epson PowerLite 480 PDF manuals and user guides View all Epson PowerLite 480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

4 Replace the cable cover and tighten the screws. 5 Plug in and turn on the projector. 6 To configure your projector for your wireless network, do one of the following: • If you're using the optional Quick Wireless Connection USB key (Windows only), insert it into the projector's USB TypeA port, wait for the displayed message, remove the key, and connect it to a USB port on your computer. Follow the on-screen instructions to install the driver, then run your presentation. For details, see the online User's Guide. • If you're not using the key, continue with these steps. 7 Press the Menu button on the remote control, select the Network menu, and press . 8 Choose Network Configuration and press . 9 Select the Basic menu and press . 14 Select the type of wireless network you are using as the Wireless LAN Sys. setting. 15 If you selected Advanced connection mode, enter your network SSID (up to 32 characters) as the SSID setting. 16 If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector's IP Address, Subnet Mask, and Gateway Address, as needed. 17 To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and/or IP Address Display settings to Off. 18 When you are finished, select Complete and press again to save your settings. , then press 19 Press the Menu button to exit the menu system. 20 See "Install network software" for additional instructions. Project over a wired network Follow the steps here to configure your projector for your wired network using the projector's menu system. 1 Plug in and turn on the projector. 2 Press the Menu button on the remote control, select the Network menu, and press . 10 Select the Projector Name setting, press , and enter a name (up to 16 characters long) to identify your projector over the network. Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press to select them. Note: See the online User's Guide for information on adding passwords. 11 Select the Wireless LAN menu and press . 3 Select Network Configuration and press . 4 Select the Basic menu and press . 12 Select the Connection Mode setting, press these options: , and choose one of • Quick to connect the projector to one computer on the network • Advanced to connect the projector to multiple computers on the network 13 If you selected Quick connection mode, select the Channel setting for your wireless network and turn on the SSID Auto Setting setting. 5 Select the Projector Name setting, press , and enter a name (up to 16 characters long) to identify your projector over the network. Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press to select them. Note: See the online User's Guide for information on adding passwords.

  • 1
  • 2
  • 3
  • 4
4
Replace the cable cover and tighten the screws.
5
Plug in and turn on the projector.
6
To configure your projector for your wireless network, do one of
the following:
•
If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB
TypeA
port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide
.
•
If you’re not using the key, continue with these steps.
7
Press the
Menu
button on the remote control, select the
Network
menu, and press
.
8
Choose
Network Configuration
and press
.
9
Select the
Basic
menu and press
.
10
Select the
Projector Name
setting, press
, and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press
to select
them.
Note:
See the online
User’s Guide
for information on adding passwords.
11
Select the
Wireless LAN
menu and press
.
12
Select the
Connection Mode
setting, press
, and choose one of
these options:
•
Quick
to connect the projector to one computer on the network
•
Advanced
to connect the projector to multiple computers on
the network
13
If you selected
Quick
connection mode, select the
Channel
setting for
your wireless network and turn on the
SSID Auto Setting
setting.
14
Select the type of wireless network you are using as the
Wireless LAN
Sys.
setting.
15
If you selected
Advanced
connection mode, enter your network SSID (up
to 32 characters) as the
SSID
setting.
16
If your network assigns addresses automatically, select
IP Settings
and
turn on the
DHCP
setting. If not, turn off the
DHCP
setting and enter
the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
,
as needed.
17
To prevent the SSID and IP address from appearing on the network
standby screen, set the
SSID Display
and/or
IP Address Display
settings
to
Off
.
18
When you are finished, select
Complete
and press
, then press
again to save your settings.
19
Press the
Menu
button to exit the menu system.
20
See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the
Menu
button on the remote control, select the
Network
menu,
and press
.
3
Select
Network Configuration
and press
.
4
Select the
Basic
menu and press
.
5
Select the
Projector Name
setting, press
, and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press
to select
them.
Note:
See the online
User’s Guide
for information on adding passwords.