Epson PowerLite 8150i RS-232 Reference Manual (ESC/VP)
Epson PowerLite 8150i Manual
 |
View all Epson PowerLite 8150i manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson PowerLite 8150i manual content summary:
- Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 1
] [Serial cable connection diagram] 4. COMMAND TYPES ...4 5. COMMAND STRUCTURE...5 6. CONTROL CODE ...9 00 SPECIAL CONTROL 9 03 : Power 06 : Communication rate 09 : Lamp Hour 12 : Error information 16 : Key codes 01 SCREEN CONTROL 11 00 : Input Source 01 : Input mode 02 : Freeze 03 : A/V Mute - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 2
correction. The power on command of EMP-7600/5600. Addition audio control commands 1. OUTLINE This manual describes the ESC/VP Level 6 protocol for communication with projectors manufactured by Seiko Epson. The manual is an abridged edition which summarizes the most commonly-used functions. If - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 3
that ESC/VP commands can be sent from the computer to the projector. [Communication Conditions] • Communication Speed • Bit length • Parity • Stop bit • Flow control Standard speed: 9600 bps 8 bit None 1 bit Hardware (DTR/DSR) (EMP-8100/9100/8150/7700: 9600 to 57600 bps) (EMP-7600/5600: 9600 to - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 4
Manual (Abridged Edition) 4. COMMAND TYPES The types of commands used can be divided into apply commands and reply commands. Both of these command types can be further divided into setting commands, acquisition commands and initialization commands. Apply commands are used to make settings - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 5
the power status over a serial connection 1D 000x 02 01 00 03 01 CS ---> 0x0008 (3) Attribute : Indicates attributes such as apply command/reply command, OK/Not OK, etc. (1 byte) The attribute codes are shown below. Table 5-1. Attribute of the Apply command Attribute Set Get Initialize Package - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 6
RS-232C communication) Master projector or stand-alone projector Code (bit) 0x00 0x01 The apply/reply codes using FromTo combinations are shown below. Table 5-4. List of FromTo codes for apply commands From PC (Serial) To Projector (Master) Apply 0x01 Table 5-5. List of FromTo codes for reply - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 7
Item Functional Code classification Power Communication rate Initialize all Lamp on Cursor Speed Password Error Information Administrator Log on Administrator Log off Key code Serial command Max/Min Alert Product ID Software version Protocol version Input source Input mode Freeze A/V Mute Volume - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 8
(2 bytes) is set. Table 5-9. List of error parameters Parameters 0x0001 Error type Network in use 0x0002 No applicable setting 0x0003 0x0004 0x0005 0x0006 0x0007 0x0008 0x0009 0x000A Resource error Download in progress Setting not currently possible Lamp off Error between projector and EasyMP - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 9
Param Checketer sum STX Size Reply Attribu te From To Group Item Param Checketer sum 03 : Power Controls the projector power and gets the present power state. Set 1B 07 01 -- 00 03 01 F4 1B 06 81 C1 -- 00 03 -- CS - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 10
Manual (Abridged Edition) 00 SPECIAL CONTROL Command Bit 0: 0 = key OFF, 1 = key ON Bit 1: 0 = shift key OFF, 1 = shift key ON Key code length: Size of key code (2 bytes) Key code: (2 bytes) 0x0001: Power 0x070A: Keystone- Reserved: 0x00000000 (4 bytes) Set 1D 0014 01 01 00 16 PARA CS 1D - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 11
0x50: DVI 0x10: PC1 mode 0x00: No mode (NoSignal) 0xE4: PALM 0xEA: 480P 0x01: PC 0xE5: PAL60 0xEB: 720P 0xE0: NTSC 0xE6: SECAM 0xEC: 1080I 0xE1: NTSC4.43 0xE7: NTSC50 0xED: 1080P 0xE2: PAL 0xE8: YCrCb(50Hz) 0xD0: Not Supported 0xE3: PALN 0xE9: YCrCb(60Hz) Set - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 12
Manual (Abridged Edition) 02 AUDIO CONTROL Command audio input. [Parameter] Volume Value (1 byte) Setting range: 00 to 1F Set 1D 0009 01 FT 02 00 PARA CS 1D Initialize 1D 0008 03 FT 02 08 -- CS 1D 0009 000A 83 C3 FT 02 08 PARA CS 09 : SRS CENTER (Applicable models: EMP - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 13
Communication Manual (Abridged Edition) 03 PC CONTROL Command structure Initialize 1D 0008 03 01 03 03 -- CS 1D 000A 000A 83 C3 10 03 03 PARA CS 0D : Sharpness Controls the screen sharpness for the currently-selected PC input source. [Parameter] Sharpness Value (1 byte) Setting - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 14
Manual (Abridged Edition) 03 PC CONTROL Command 2 Set 1D Initialize 1D 0008 03 01 03 0E -- CS 1D 0009 000A 83 C3 10 03 0E 12 : Automatic setup (* Only valid for Standalone/Master projector) Reports the start and end of automatic setup. [Parameter] Data relating to automatic setup - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 15
Manual (Abridged Edition) 04 VIDEO CONTROL Command structure Type STX Apply Size Attribu From te To Group Item Param Checketer sum STX 00 : Brightness Controls the screen brightness for the currently-selected video input source. [Parameter] Brightness Value (1 byte) Setting - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 16
] Data relating to video mode * The video signal method will be automatically set up in the [Auto] mode, but do not use the [Auto] mode for the PAL system (60Hz CS Initialize 1D 0008 03 01 04 05 -- CS 1D 0009 000A 83 C3 10 04 05 PARA CS 06 : Smooth Motion (Applicable models: EMP-8100/ - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 17
ESC/VP Level 6 Serial Communication Manual (Abridged Edition) 05 DISPLAY CONTROL Command structure Type STX Apply Size Attribu From te To is on or off 0x00: OFF 0x01: ON Set 1D 0009 01 01 05 02 PARA CS 1D Get 1D 0008 02 01 05 02 -- CS 1D Initialize 1D 0008 03 01 05 02 -- CS 1D - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 18
10 06 04 PARA CS 09 : BNC Input Source Type (Applicable models: EMP-8100/8150/9100/7700) Controls the input format for the BNC connector. [Parameter] Data relating to input format for the BNC connector 0x00: RGB 0x01: YCrCb 0x02: YPbPr Set 1D 0008 01 01 06 09 PARA CS 1D 0008 000A 81 - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 19
14 PARA CS Initialize 1D 0008 03 01 06 14 -- CS 1D 0009 000A 83 C3 10 06 14 PARA CS 15 : DelayON (Applicable models: EMP-8100/8150/9100/7700) Controls the DelayOn ON/OFF setting. When set to ON, the lamp is on when power is being supplied through the power cable. When set to OFF, this - Epson PowerLite 8150i | RS-232 Reference Manual (ESC/VP) - Page 20
Level 6 Serial Communication Manual (Abridged Edition) 07 CUSTOM Command structure Type STX Apply 0009 02 01 07 08 -- CS 1D Initialize 1D 0008 03 01 07 08 -- CS 1D 09 : PinP audio selection setting (Applicable models: EMP-7600/5600) Controls the audio selections which are enabled
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
ESC/VP Level 6 Serial Communication Manual (Abridged Edition)
1 of 20
ESC/VP Level 6 Serial Communication Manual (Abridged Edition) Ver.3
Table of Contents
REVISION STATUS
....................................................................................................................................................
2
1. OUTLINE
................................................................................................................................................................
2
2. APPLICATION
........................................................................................................................................................
2
3. SERIAL COMMUNICATION SPECIFICATIONS
...................................................................................................
3
4. COMMAND TYPES
................................................................................................................................................
4
5. COMMAND STRUCTURE
......................................................................................................................................
5
6. CONTROL CODE
...................................................................................................................................................
9
[Communication Conditions]
[Connectors]
[Serial cable connection diagram]
00 SPECIAL CONTROL
...............................................
9
03 : Power
06 : Communication rate
09 : Lamp Hour
12 : Error information
16 : Key codes
01 SCREEN CONTROL
.............................................
11
00 : Input Source
01 : Input mode
02 : Freeze
03 : A/V Mute
02 AUDIO CONTROL
.................................................
12
00 : Volume
06 : Bass
07 : Treble
08 : SRS SPACE
09 : SRS CENTER
03 PC CONTROL
.......................................................
13
00 : Brightness
01 : Contrast
02 : Sync.
03 : Tracking
0D : Sharpness
0E : Input Resolution
12 : Automatic setup
04 VIDEO CONTROL
.................................................
15
00 : Brightness
01 : Contrast
02 : Sharpness
03 : Saturation
04 : Tint
05 : Video Mode
06 : Smooth Motion
05 DISPLAY CONTROL
.............................................
17
02 : Rear Proj.
03 : Ceiling
06 OPTION
.................................................................
18
03 : Source Prompt
04 : Blank
09 : BNC Input Source Type
0F : Keystone
10 : Start up Screen
11 : Message
14 : V Keystone
15 : DelayON
16 : Comp1/DV1 selection
19 : Computer2 input format
07 CUSTOM
...............................................................
20
08 : PinP
09 : PinP audio selection setting