Epson PowerLite 955W Quick Setup - Page 3

Project over a wirednetwork

Get Epson PowerLite 955W PDF manuals and user guides View all Epson PowerLite 955W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

4 Attach the wireless LAN module cover and secure it using the screw you removed. 5 Press the Menu button on the remote control, select the Network menu, and press . 11 To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and IP Address Display settings to Off. 12 When you're finished selecting settings in the Wireless LAN menu, press Esc. 13 If you are connecting the projector to a secure network, select the Security menu and press . Then select settings and press Esc when you're finished. 14 S elect Complete and press save your settings. , then select Yes and press again to 15 S ee "Install network software" for additional instructions. 6 Choose Network Configuration and press . 7 Select the Wireless LAN menu and press . Project over a wired network Follow the steps here to configure your projector for your wired network using the projector's menu system. 1 Plug in and turn on the projector. 2 Press the Menu button on the remote control, select the Network menu, and press . 8 Choose Connection Mode, press , select Quick (for a direct connection to a computer, tablet, or smartphone) or Advanced (for a connection to a router or access point), then press again. When you're finished, press Esc to return to the Wireless LAN menu. 9 If you chose the Advanced connection mode, select SSID, press and enter your network name (SSID) on the screen that appears. 3 Select Network Configuration and press . 4 Select the Basic menu and press . • To select a number or character, use the arrow buttons on the remote control to highlight it, then press . • To switch between uppercase and lowercase letters, select CAPS and press . • To change the displayed symbols, select SYM1 or SYM2 and press . When you're finished entering the SSID, select Finish and press . 10 If you chose the Advanced connection mode, select IP settings and press . If your network assigns addresses automatically, turn on DHCP. If not, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address, as needed. To enter numbers, use the arrow buttons on the remote control to highlight a number, then press the button. When you're finished entering an address, highlight Finish, then press . Press Esc. 5 Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network. Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press to select them. Note: See the online User's Guide for information on adding passwords.

  • 1
  • 2
  • 3
  • 4
4
Attach the wireless LAN module cover and secure it using the screw you
removed.
5
Press the
Menu
button on the remote control, select the
Network
menu,
and press
.
6
Choose
Network Configuration
and press
.
7
Select the
Wireless LAN
menu and press
.
8
Choose
Connection Mode
, press
, select
Quick
(for a direct
connection to a computer, tablet, or smartphone) or
Advanced
(for
a connection to a router or access point), then press
again. When
you’re finished, press
Esc
to return to the Wireless LAN menu.
9
If you chose the Advanced connection mode, select
SSID
, press
and
enter your network name (SSID) on the screen that appears.
•
To select a number or character, use the arrow buttons on the remote
control to highlight it, then press
.
•
To switch between uppercase and lowercase letters, select
CAPS
and
press
.
•
To change the displayed symbols, select
SYM1
or
SYM2
and
press
.
When you’re finished entering the SSID, select
Finish
and press
.
10
If you chose the Advanced connection mode, select
IP settings
and
press
.
If your network assigns addresses automatically, turn on
DHCP
. If not,
turn off
DHCP
and enter the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the
button. When you’re finished
entering an address, highlight
Finish
, then press
. Press
Esc
.
11
To prevent the SSID and IP address from appearing on the network
standby screen, set the
SSID Display
and
IP Address Display
settings to
Off
.
12
When you’re finished selecting settings in the Wireless LAN menu,
press
Esc
.
13
If you are connecting the projector to a secure network, select the
Security
menu and press
. Then select settings and press
Esc
when
you’re finished.
14
Select
Complete
and press
, then select
Yes
and press
again to
save your settings.
15
See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the
Menu
button on the remote control, select the
Network
menu,
and press
.
3
Select
Network Configuration
and press
.
4
Select the
Basic
menu and press
.
5
Select the
Projector Name
setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press
to select
them.
Note:
See the online
User’s Guide
for information on adding passwords.