Fisher and Paykel DE62T27CW2 AeroSmart LCD Models Installation Instructions &a - Page 27

wire connections

Get Fisher and Paykel DE62T27CW2 PDF manuals and user guides View all Fisher and Paykel DE62T27CW2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installation instructions 25 3-wire connections For use where local codes permit grounding through the Neutral wire. Use approved 3-wire Power Supply Cord or a 3-wire Cable for Direct Wiring as described on page 23. 1 Remove the terminal block cover plate. 2 Insert the power cord with a UL listed strain relief through the hole provided in the cabinet near the terminal block. Do not tighten strain relief screw until wiring connections are complete. Note: a strain relief must be used. 2 strain relief clamp sections strain relief screws Fig.23 Inserting the power cord 3 Loosen or remove the center terminal block screw. Connect the neutral wire (center) of the power supply cord to the center terminal screw of the terminal block. Tighten screw. 4 Connect the other wires to the upper and lower terminal block screws marked with the letter L. Tighten screws. 4 3 Fig.24 Connecting the wires 4 5 Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer. Secure cover with securing screw. 6 Tighten strain relief screws. 5 6 Fig.25 Refitting terminal block cover Fig.26 Tightening strain relief screws

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
25
Installation instructions
3-wire connections
For use where local codes
permit
grounding through the Neutral wire.
Use approved 3-wire Power Supply Cord or a 3-wire Cable for Direct Wiring as described on
page 23.
1
Remove the terminal block cover plate.
2
Insert the power cord with a UL listed strain relief through the hole provided in the cabinet near
the terminal block. Do not tighten strain relief screw until wiring connections are complete.
Note: a strain relief must be used.
2
strain relief
clamp sections
strain relief
screws
Fig.23 Inserting the power cord
3
Loosen or remove the center terminal block screw. Connect the neutral wire (center) of the
power supply cord to the center terminal screw of the terminal block. Tighten screw.
4
Connect the other wires to the upper and lower terminal block screws marked with the letter L.
Tighten screws.
4
3
4
Fig.24 Connecting the wires
5
Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer. Secure
cover with securing screw.
6
Tighten strain relief screws.
5
6
Fig.26 Tightening strain relief screws
Fig.25 Refitting terminal block cover