Fisher and Paykel DE62T27CW2 AeroSmart LCD Models Installation Instructions &a - Page 29

Use approved 4-wire Power Supply Cord or a 4-wire Cable for Direct Wiring as described,

Get Fisher and Paykel DE62T27CW2 PDF manuals and user guides View all Fisher and Paykel DE62T27CW2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Installation instructions 27 4-wire connections Use approved 4-wire Power Supply Cord or a 4-wire Cable for Direct Wiring as described on page 24. 1 Remove the terminal block cover plate. 2 Insert the power supply cable with a UL listed strain relief through the hole provided in the cabinet near the terminal block. Do not tighten strain relief screw until wiring connections are complete. Note: a strain relief must be used. 2 strain relief clamp sections strain relief screws 3 Remove center terminal block screw. Fig.30 Inserting the power cord 4 Remove appliance ground link by removing the ground connector screw (green screw). 3 4 Note: If the appliance is moved back to a 3-wire installation the ground link must be refitted. Remove link Fig.31 Removing screws 5 Connect ground wire (green) of the power supply cord to the ground conductor green screw. Tighten screw. 6 Connect the neutral wire (white) of the power supply cord to the center terminal screw of the terminal block. Tighten screw. 7 Connect the red wire and black wire to the upper and lower terminal block screws marked with the letter L. Tighten screws. 7 6 5 Fig.32 Connecting wiring 7 8 Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer and secure cover with securing screw. 9 Tighten Strain Relief screws. 8 9 Fig.33 Refitting terminal block and screws

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
27
Installation instructions
4-wire connections
Use approved 4-wire Power Supply Cord or a 4-wire Cable for Direct Wiring as described
on page 24.
1
Remove the terminal block cover plate.
2
Insert the power supply cable with a UL listed strain relief through the hole provided in the cabinet
near the terminal block. Do not tighten strain relief screw until wiring connections are complete.
Note: a strain relief must be used.
2
strain relief
clamp sections
strain relief
screws
Fig.30 Inserting the power cord
3
Remove center terminal block screw.
4
Remove appliance ground link by removing the ground connector screw (green screw).
3
4
Remove link
Note: If the appliance is moved back to a 3-wire
installation the ground link must be refitted.
Fig.31 Removing screws
5
Connect ground wire (green) of the power supply cord to the ground conductor green screw.
Tighten screw.
6
Connect the neutral wire (white) of the power supply cord to the center terminal screw of the
terminal block. Tighten screw.
7
Connect the red wire and black wire to the upper and lower terminal block screws marked with
the letter L. Tighten screws.
Fig.32 Connecting wiring
7
6
5
7
8
Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer and
secure cover with securing screw.
9
Tighten Strain Relief screws.
8
9
Fig.33 Refitting terminal block and screws