Fisher and Paykel E522BRXU2 ActiveSmart Ice & Water Refrigerator User Guid - Page 12

connections are dry and free of drips.

Get Fisher and Paykel E522BRXU2 PDF manuals and user guides View all Fisher and Paykel E522BRXU2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

US 10 Installation instructions CA 11 Attach double sided foam to the back of the water filter head as shown in Diagram 5. Write the date to be replaced on the filter (date installed + 6 months). Remove double sided foam backing and attach filter to the desired position as located in step 10 (refer to previous page). 12 Run the ¼" (6 mm) tubing to back of the refrigerator ensuring there is enough tubing to pull out the refrigerator for service. 13 Remove compressor compartment cover by removing screw at the top of each side of the cover as shown in Diagram 6. Lift and tilt the compressor compartment cover to remove as shown in Diagram 7. 14 Connect tubing into the water (solenoid) valve located on the right hand side of the unit (compressor) compartment as shown in Diagram 8. Beware of hot pipes. 15 Pull gently on tubing to ensure it is locked in as shown in Diagram 9. 16 Place compressor compartment cover back into position, run the ¼" (6 mm) tubing through the space provided at the top right hand side of the compressor compartment cover in an upward direction and rescrew the compressor compartment cover as shown in Diagram 10. 17 The completed installation should look like Diagram 12 on page 11. 18 Turn isolating faucet on and check that all connections are dry and free of drips. 19 Coil water line tubing behind the refrigerator. Push your refrigerator into place being careful not to kink or squash the water line running into the water (solenoid) valve. 20 Read pages 12 - 14 carefully and then turn refrigerator on. 21 The first time you require water out of the dispenser, there will be a delay while the water reservoir fills up. 22 Run a further 3 qt (3 L) through the system, stopping intermittently to ensure the reservoir is flushed out. Failure to do this will result in excessive dripping from your dispenser. Diagram 6 Diagram 7 Diagram 8 Diagram 10 Diagram 5 Fig.7 Double sided foam attachment Diagram 9 Fig.8 Waterline connection to refrigerator

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Installation instructions
11
Attach double sided foam to the back of the
water filter head as shown in Diagram 5. Write
the date to be replaced on the filter (date
installed + 6 months). Remove double sided foam
backing and attach filter to the desired position
as located in step 10 (refer to previous page).
12
Run the ¼” (6 mm) tubing to back of the
refrigerator ensuring there is enough tubing to
pull out the refrigerator for service.
13
Remove compressor compartment cover by
removing screw at the top of each side of the
cover as shown in Diagram 6. Lift and tilt the
compressor compartment cover to remove as
shown in Diagram 7.
14
Connect tubing into the water (solenoid)
valve located on the right hand side of the
unit (compressor) compartment as shown in
Diagram 8. Beware of hot pipes.
15
Pull gently on tubing to ensure it is locked in as
shown in Diagram 9.
16
Place compressor compartment cover back into
position, run the ¼” (6 mm)
tubing through the space provided at the top
right hand side of the compressor compartment
cover in an upward direction and rescrew the
compressor compartment cover as shown in
Diagram 10.
17
The completed installation should look like
Diagram 12 on page 11.
18
Turn isolating faucet on and check that all
connections are dry and free of drips.
19
Coil water line tubing behind the refrigerator.
Push your refrigerator into place being careful
not to kink or squash the water line running into
the water (solenoid) valve.
20
Read pages 12 – 14 carefully and then turn
refrigerator on.
21
The first time you require water out of the
dispenser, there will be a delay while the water
reservoir fills up.
22
Run a further 3 qt (3 L) through the system,
stopping intermittently to ensure the reservoir
is flushed out. Failure to do this will result in
excessive dripping from your dispenser.
Fig.8 Waterline connection to refrigerator
Diagram 5
Fig.7 Double sided
foam attachment
Diagram 7
Diagram 10
Diagram 9
Diagram 8
Diagram 6
US
CA
10