Fluke 831 Product Manual - Page 53

XY View

Get Fluke 831 PDF manuals and user guides View all Fluke 831 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

On-board help XY View The XY View function is used to help center the laser beam on the position detector before measurement can continue. l Tap the shown detector area (1) to directly access the XY View screen. l The XY View screen can be accessed through the menu item "XY View" which is shown when the "sensor area" (2) is tapped. l The XY View screen can be accessed through the menu item "XY View" which is shown when the reflector (3) is tapped. Displayed are the absolute X,Y coordinates of the laser beam on the position detector, the angle at which the sensor is currently positioned on the shaft and the sensor serial number. Use the adjustment knob and the adjustment thumbwheel to center the laser beam dot on the position detector. In some cases it can be necessary to move the sensor along the support posts or sideways. To move sensor sideways, loosen the chain type bracket then slightly rotate the bracket. The "Set to zero" function may be used to check the effect of environmental and machinery vibration on the measurement. Note: "Set to zero" is active only when the laser beam status [1] is "OK" or "Centered". MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
XY View
The XY View function is used to help center the laser beam on the position detector before
measurement can continue.
l
Tap the shown detector area
(1)
to directly access the XY View screen.
l
The XY View screen can be accessed through the menu item "XY View" which is shown
when the "sensor area"
(2)
is tapped.
l
The XY View screen can be accessed through the menu item "XY View" which is shown
when the reflector
(3)
is tapped.
Displayed are the absolute X,Y coordinates of the laser beam on the position detector, the
angle at which the sensor is currently positioned on the shaft and the sensor serial number.
Use the adjustment knob and the adjustment thumbwheel to center the laser beam dot on the
position detector. In some cases it can be necessary to move the sensor along the support
posts or sideways. To move sensor sideways, loosen the chain type bracket then slightly rotate
the bracket.
The "Set to zero" function may be used to check the effect of environmental and machinery
vibration on the measurement.
Note:
"Set to zero" is active only when the laser beam status [
1
] is "OK" or "Centered".
On-board help
Shop for Fluke products online at:
1.888.610.7664
www.
MyFlukeStore
.com