Home » Fluke Manuals » Electronics Accessories » Fluke 9103-A-156 » Manual Viewer

Fluke 9103-A-156 Product Manual - Page 28

Menu Legend

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

DO NOT CHANGE THESE VALUES. SEE MANUAL 9103 Dry-Well User's Guide Display Temperature SET Select Setpoint Adjust Setpoint Units °C/°F Scan On/Off Scan Rate UP Hold Temperature Display DOWN SET + DOWN Displays Set-Point Resistance EXIT SET + UP Toggles °C / °F EXIT Secondary Functions SET + EXIT Display Power Set Proportional Band Configuration Menu SET EXIT Operating Parameters Menu SET HL Adj.HL UP DOWN Menu Legend: Press "SET" to step through the menu and to store the parameter value. Press "EXIT" briefly to skip a parameter without storing the parameter value. Hold "EXIT" to exit the menu and display the temperature Figure 4 Controller Operation Flowchart EXIT Serial Interface Menu SET BAUD Rate Adjust BAUD Rate Sample Period Adj. Sample Period Duplex Mode Adj. Duplex Mode Linefeed Adjust Linefeed UP DOWN DO NOT CHANGE THESE VALUES. SEE MANUAL EXIT Cal Menu SET X5 R0 Adj. R0 ALPHA Adj. ALPHA DELTA Adj. DELTA BETA Adjust BETA 20 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

Section	Page
Model 9103 Dry-Well	1
Warranty	2
Table of Contents	3
Figures	6
Tables	7
1 Before You Start	9
1.1 Symbols Used	9
1.2 Safety Information	10
1.2.1 Warnings	10
1.2.2 Cautions	11
1.3 Authorized Service Centers	11
2 Introduction	15
3 Specifications and EnvironmentalConditions	17
3.1 Specifications	17
3.2 Environmental Conditions	17
3.3 Warranty	19
4.1 Unpacking	19
4.2 Setup	19
4.3 Power	19
4.4 Setting the Temperature	20
5 Parts and Controls	21
5.1 Back Panel	21
5.2 Front Panel	21
5.3 Constant Temperature Block Assembly	23
5.4 Probe Sleeves	23
6 General	25
6.1 Changing Display Units	25
6.2 Thermal Electric Devices (TED)	25
7 Controller Operation	27
7.1 Well Temperature	27
7.2 Temperature Set-point	27
7.2.1 Programmable Set-points	27
7.2.2 Set-point Value	29
7.2.3 Temperature Scale Units	29
7.3 Scan	30
7.3.1 Scan Control	30
7.3.2 Scan Rate	30
7.4 Temperature Display Hold	30
7.4.1 Enabling the Hold Temperature Display	31
7.4.2 Mode Setting	31
7.4.3 Switch Wiring	31
7.4.4 Switch Test Example	32
7.5 Set-point Resistance	32
7.6 Temperature Scale Units	32
7.7 Secondary Menu	32
7.8 Thermal Electric Devices (TED)	33
7.9 Proportional Band	33
7.10 Controller Configuration	34
7.11 Operating Parameters	34
7.12 Serial Interface Parameters	35
7.12.1 BAUD Rate	35
7.12.2 Sample Period	36
7.12.3 Duplex Mode	36
7.12.4 Linefeed	36
7.13 Calibration Parameters	37
7.13.1 R0	37
7.13.2 ALPHA	37
7.13.3 DELTA	38
7.13.4 BETA	38
8 Digital Communication Interface	39
8.1 Serial Communications	39
8.1.1 Wiring	39
8.1.2 Setup	39
8.1.2.1 BAUD Rate	40
8.1.2.2 Sample Period	40
8.1.2.3 Duplex Mode	40
8.1.2.4 Linefeed	40
8.1.3 Serial Operation	41
8.2 Interface Commands	41
9 Test Probe Calibration	45
9.1 Calibrating a Single Probe	45
9.2 Stabilization and Accuracy	45
10 Calibration Procedure	47
10.1 Calibration Points	47
10.2 Calibration Procedure	47
10.2.1 Compute DELTA	47
10.2.2 Compute R0 and ALPHA	48
10.2.3 Compute BETA	49
10.2.4 Accuracy and Repeatability	49
11 Maintenance	51
12 Trouble Shooting	53
12.1 Troubleshooting	53
12.2 CE Comments	54
12.2.1 EMC Directive	54