Foxconn B75MX-D User manual - Page 23

Front Panel Header: FP1, Serial ATA Connectors: SATA_1/2/3/4, Hard Disk LED Connector HDD-LED

Get Foxconn B75MX-D PDF manuals and user guides View all Foxconn B75MX-D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

HARDWARE INSTALLATION Front Panel Header: FP1 This motherboard includes one connector for connecting the front panel switch and LED Indicators. Hard Disk LED Connector (HDD-LED) Connect to the chassis front panel IDE indicator LED. It indicates the active status of the hard disks. This 2-pin connector is directional with +/- sign. Reset Switch (RESET-SW) Attach the connector to the Reset switch on the front panel of the case; the system will restart when the switch is pressed. Power LED Connector (PWR-LED) Connect to the power LED indicator on the front panel of the chassis. The Power LED indicates the system's status. When the system is in operation (S0 status), the LED is on. When the system gets into sleep mode (S1) , the LED is blinking; When the system is in S3/S4 sleep state or power off mode (S5), the LED is off. This 2-pin connector is directional with +/- sign. Power Switch Connector (PWR-SW) Connect to the power button on the front panel of the chassis. Push this switch allows the system to be turned on and off rather than using the power supply button. 12 + HDD-LED - + - PWR-LED RESET-SW PWR-SW NC EMPTY 9 10 FP1 Serial ATA Connectors: SATA_1/2/3/4 The Serial ATA connector is used to connect with SATA Hard Disk or CD devices which support this feature. The SATA_2/3/4 allows up to 3GB/s data transfer rate, the SATA_1 support SATA 3.0 specification, and allows up to 6GB/s data transfer rate. 1 GND TX+ TXGND RXRX+ GND 1 GND TX+ TXGND RXRX+ GND SATA_1 SATA_2/3/4 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
HARDWARE INSTALLATION
16
SATA_2/3/4
GND
TX+
TX-
GND
RX-
RX+
GND
1
GND
TX+
TX-
GND
RX-
RX+
GND
1
SATA_1
Front Panel Header: FP1
This motherboard includes one connector for
connecting the front panel switch and LED
Indicators.
Hard Disk LED Connector (HDD-LED)
Connect to the chassis front panel IDE
indicator LED. It indicates the active status
of the hard disks. This 2-pin connector is
directional with +/- sign.
Reset Switch (RESET-SW)
Attach the connector to the Reset switch on the
front panel of the case; the system will restart
when the switch is pressed.
Power LED Connector (PWR-LED)
Connect to the power LED indicator on the
front panel of the chassis. The Power LED
indicates the system’s status. When the
system is in operation (S0 status), the LED is
on. When the system gets into sleep mode (S1)
, the LED is blinking; When the system is in
S3/S4 sleep state or power off mode (S5), the
LED is off. This 2-pin connector is directional
with +/- sign.
Power Switch Connector (PWR-SW)
Connect to the power button on the front
panel of the chassis. Push this switch allows
the system to be turned on and off rather than
using the power supply button.
Serial ATA Connectors: SATA_1/2/3/4
The Serial ATA connector is used to connect with
SATA Hard Disk or CD devices which support this
feature. The SATA_2/3/4 allows up to 3GB/s
data transfer rate, the SATA_1 support SATA
3.0 specification, and allows up to 6GB/s data
transfer rate.
HDD-LED
RESET-SW
NC
+
-
-
PWR-SW
+
PWR-LED
EMPTY
FP1
1
2
10
9