Frigidaire AEQ6000ES Installation Instructions - Page 7
ALL GAS Dryers - manual
UPC - 012505374906
View all Frigidaire AEQ6000ES manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
ELECTRICAL INSTALLATION ELECTRIC Dryer ALL GAS Dryers The following are specific requirements for proper and safe electrical installation of your dryer. Failure to follow these instructions can create electrical shock and/or a fire hazard. This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/or fire hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the pre-installation requirements in this manual for the proper power cord to be purchased. A U.L. approved strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle. NOTE: Dryers operating on 208 volt power supply will have longer drying times than operating on 240 volt power supply. GROUNDING REQUIREMENTS NON-CANADIAN ELECTRIC Dryer Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. If your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. Do not modify plug provided with the appliance. For a permanently connected dryer: 1. The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the appliance. This dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. ELECTRICAL CONNECTIONSFOR 3-WIRE SYSTEM NON-CANADIAN ELECTRIC Dryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper cor ner. 2. Install a U.L. approved strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time. 3. Thread a U.L. approved 30 amp. power cord, NEMA 10-30 type SRDT, through the strain relief. 4. Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw s e c u r e l y. 5. Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tighten both screws s e c u r e l y. Do not make a sharp bend or crimp wiring/ conductor at connections. 6. Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely. GREEN GROUND SCREW NEUTRAL GROUND WIRE SILVER TERMINAL NUT TIGHTEN NUT TO THESE THREADS Canadian ELECTRIC Dryer DANGER Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. STRAIN RELIEF MOUNTING BRACKET POWER CORD 7. Tighten the screws securing the cord restraint firmly against the power cord. 8. Tighten the strain relief nut securely so the strain relief does not turn. 9. Reinstall the terminal block cover. 2. Since your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. Do not modify plug provided with the appliance. 7