Frigidaire FHWC3625MW Use and Care Manual - Page 10

INSTALL RANGE HOOD, Ducted version, PREPARE THE LOCATION

Get Frigidaire FHWC3625MW PDF manuals and user guides View all Frigidaire FHWC3625MW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

PREPARE THE LOCATION Style 3 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm) Rectangular Vent Transition to Round Vent Roof Venting To make a circular vent opening on the underside of the cabinet top: 1.Mark a centerline on the underside of the top of cabinet. .Mark a line 5" (12.7 cm) from the back wall on the underside of the top of cabinet. .Use a compass or a circle template to draw a circle with a diameter of 7½" (19 cm). Use saber or keyhole saw to cut the circular vent opening. Ø 7½" Centerline (19 cm) *5" (12.7 cm) Cabinet cutouts *From wall, not cabinet frame Install Vent System 1.Install vent through the vent opening in upper cabinet or wall. Complete venting system according to the selected venting method. See "Venting Requirements" section. .Use caulking to seal exterior wall or roof opening around the cap. INSTALL RANGE HOOD (Ducted version) NOTE Your model will have a 3¼" x 10" (8.3 x 25.4 cm) rectangular vent connector on the inside of the range hood. 1.Unpack the 3¼" x 10" (8.3 x 25.4 cm) rectangular vent from the inside of your range hood. To detach the vent connector, remove the 2 installation screws (.35x .95cm) and keep the screws in a safe place to reinstall later (see Step 5). Style 4 - Cut Openings for 7" (17.8 cm) Round Vent to Round Vent Transition Roof Venting To make a circular vent opening on the underside of the cabinet top: NOTE: The 7" round transition kit, part number 5304487139, is required for this installation. 1.Mark a centerline on the underside of the top of cabinet. .Mark a line 5" (12.7 cm) from the back wall on the underside of the top of cabinet. .Use a compass or a circle template to draw a circle with a diameter of 7½" (19 cm). Use saber or keyhole saw to cut the circular vent opening. 4.Repeat steps 1-3 for the underside of the top of the cabinet. *Ø 7½" Centerline (19 cm) * *5" (12.7 cm) * Cabinet cutouts 10 *From wall, not cabinet frame A. 3¼" x 10" (8.3 x 25.4 cm) rectangular vent damper A B. 3.5 x 9.5 mm screws B .Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood (See slot dimensions on page 6). Set range hood aside on a covered surface. A A A. Keyhole slot

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
10
Install Vent System
Install vent through the vent opening in upper cabinet
or wall. Complete venting system according to the
selected venting method. See “Venting Requirements”
section.
Use caulking to seal exterior wall or roof opening
around the cap.
INSTALL RANGE HOOD
(Ducted version)
NOTE
Your model will have a 3¼” x 10” (8.3 x 25.4
cm) rectangular vent connector on the inside of
the range hood.
Unpack the 3¼” x 10” (8.3 x 25.4 cm) rectangular
vent from the inside of your range hood. To detach the
vent connector, remove the 2 installation screws
(.35x .95cm) and keep the screws in a safe place to
reinstall later (see Step 5).
Lift the range hood up under cabinet and determine
final location by centering beneath cabinet. Mark on
the underside of cabinet the location of the 4 keyhole
mounting slots on the range hood (See slot dimensions
on page 6). Set range hood aside on a covered surface.
1.
±.
1.
±.
A
A. Keyhole slot
A
A
B
A. 3¼” x 10” (8.3 x 25.4 cm) rectangular vent damper
B. 3.5 x 9.5 mm screws
PREPARE THE LOCATION
Style 3 - Cut Openings for 3¼” x 10” (8.3 x 25.4
cm) Rectangular Vent Transition to Round Vent
Roof Venting
To make a circular vent opening on the underside of the
cabinet top:
Mark a centerline on the underside of the top of cabinet.
Mark a line 5” (12.7 cm) from the back wall on the
underside of the top of cabinet.
Use a compass or a circle template to draw a circle with
a diameter of 7½” (19 cm).
Use saber or keyhole saw to cut the circular vent
opening.
Style 4 - Cut Openings for µ” (1µ.8 cm) Round Vent
to Round Vent Transition
Roof Venting
To make a circular vent opening on the underside of the
cabinet top:
NOTE:
The 7” round transition kit, part number
5304487139, is required for this installation.
Mark a centerline on the underside of the top of cabinet.
Mark a line 5” (12.7 cm) from the back wall on the
underside of the top of cabinet.
Use a compass or a circle template to draw a circle with
a diameter of 7½” (19 cm).
Use saber or keyhole saw to cut the circular vent opening.
Repeat steps 1-3 for the underside of the top of the
cabinet.
1.
±.
².
1.
±.
².
4.
*From wall, not
cabinet frame
*5”
(12.7 cm)
Cabinet
cutouts
Ø 7½”
(19 cm)
Centerline
*From wall, not
cabinet frame
*5”
*
*
(12.7 cm)
Cabinet
cutouts
*Ø 7½”
(19 cm)
Centerline