Frigidaire FPES3085KF Installation Instructions (All Languages) - Page 8

30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS 4. Cabinet Construction 4.1 To eliminate the risk of burns or fire by reaching over heated surface units, do not have cabinet storage space above the range. If there is cabinet storage space above range, reduce risk by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinet. 4.2 Countertop Preparation • The cooktop sides of the range fit over the cutout edge of your countertop. • If you have a square finish (flat) countertop, no countertop preparation is required. Cooktop sides lay directly on edge of countertop. • Formed front-edged countertops must have molded edge shaved flat 3/4" (1.9 cm) from each front corner of opening (Figure 7). • Tile countertops may need trim cut back 3/4"(1.9 cm) from each front corner and/or rounded edge flattened (Figure 7). Min. Cutout Width ¾" (1.9 cm) ¾" (1.9 cm) 31½" (81 cm) Formed or tile countertop trimmed ¾" (1.9 cm) back at front corners of countertop opening. Figure 7 • If the existing cutout width is greater than 30 1/16" (76,4 cm), reduce the ¾" (1.9 cm) dimension. • Countertop must be level. Place a level on the countertop, first side to side, then front to back. If the countertop is not level, the range will not be level. The oven must be level for satisfactory baking results. Cooktop sides of range fit over edges of countertop opening 5. Range Installation Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. Refer to the Use and Care Guide for oven door removal instructions. Standard Installation The range cooktop overlaps the countertop at the 1 sides and the range rests on the floor. The cooktop is 31½" (80 cm) wide. Install base cabinets 30" (76.2 cm) apart. Make sure 2 they are plumb and level before attaching cooktop. Shave raised countertop edge to clear 31½" (80 cm) wide range top rim. 3 Install cabinet doors 31" (78.7 cm) min. apart so as not to interfere with range door opening. 4 Cutout countertop exactly as shown on page 1. Make sure the four leveling legs (front and rear) are 5 setup higher than the height of the cabinet (shown on page 3). Install the anti-tip bracket at this point before placing the range at its final 6 position. Follow the installation instructions at the last page or on the anti-tip bracket template supplied with the range. To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to 7 range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. To reduce the risk of damaging your 8 appliance, do not handle or manipulate it by the cooktop. Manipulate with care. 9 Position range in front of the cabinet opening. Make sure that the underside of the cooktop clears 10 the countertop. If necessary, raise the unit by lowering the leveling legs. Level the range (see section 6). The floor where 11 the range is to be installed must be level. Follow the instructions under "Leveling the Range". 12 Slide the range into the cutout opening. IMPORTANT If Accessories Needed : Installation With Backguard The cutout depth of (21 3/4" (55.2 cm)Min., 22 1/8" (56.2cm) Max.) needs to be increased to 24" (61 cm) when installing a backguard. Installation With End Panel A End Panel kit can be ordered through a Service Center. Installation With Side Panels A Side Panels kit can be ordered through a Service Center. Note: Install cabinet doors 32" (81.3 cm) min. apart so as not to interfere with range door opening. 8