Frigidaire GLTF2940FB Data Sheet - Page 4

Check, Correction

Get Frigidaire GLTF2940FB - Front Load Washer PDF manuals and user guides View all Frigidaire GLTF2940FB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Test Test 1: Check 1. Is the incoming water flow normal? Test 2. Are the incoming water faucets turned 3. Is the incoming water pressure above (30) psi. 4. Does the fill water continue enter the washer? 5. Remove power from the washer. Did the water fill stop? 6. Good models, check the pressure switch. Test 2: Test 3: 7. Better models, replace the pressure sensor. 8. Replace the control board. 1. Is the washer leaking water? 2. Is there an air leak in the air bell system? 3. Good models, check the pressure switch. 4. Better models, replace the pressure sensor. 5. Replace the control board. 1. Is the dispenser drawer closed? 2. Remove the drawer and check the magnet. Test 4: 3. Open the console and check the reed switch. 1. Check the drain hose for restrictions. 2. Start the washer and check for 120 VAC at the drain pump. Test 5: Inspect the wiring between the pressure sensor and the control board. Correction Yes. Go to step (4). No. Go to step (2) No. Turn water faucets on. Yes. Go to step (3). No. Have customer correct pressure problem. Yes. Check for kinked or blocked incoming water hoses, clean the incoming water screens. If problem still remains, replace the water inlet valve assembly. Yes. Go to step (5). No. Go to step (6) Yes. Go to step (6) No. Replace the inlet valve assembly. Pressure switch checks good. Go to step (8). Pressure switch checks bad. Replace pressure switch. If this did not correct the problem, go to step 8. Yes. Correct water leak. No. Go to step (2) Yes. Correct the air leak problem. No. Go to step (3-4) Defective. Replace the pressure switch. Good. Go to step (5) If this did not correct the problem, go to step 5. No. Close the drawer. Yes. Go to step (2). Magnet missing or defective. Replace the magnet. Magnet good. Go to step (3). Defective. Replace the reed switch. Good. Replace the control board. Restriction. Correct problem. No restriction. Go to step (2). Zero. Replace the control board. 120 VAC. Remove the pump and check for blockage. If blocked, remove the restriction, if not, replace the pump. Defective wiring. Correct wiring. Good wiring. Replace the pressure sensor. If this does not correct the problem, replace the control board. 4 P/N 134408500

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
4
Test
Test
Check
Correction
Test 1:
Test 2:
Test 3:
Test 4:
Test 5:
Yes. Go to step (4).
No. Go to step (2)
No. Turn water faucets on.
Yes. Go to step (3).
No. Have customer correct pressure
problem.
Yes. Check for kinked or blocked
incoming water hoses, clean
the incoming water screens. If
problem still remains, replace the
water inlet valve assembly.
Yes. Go to step (5).
No. Go to step (6)
Yes. Go to step (6)
No. Replace the inlet valve assembly.
Pressure switch checks good.
Go to step (8).
Pressure switch checks bad. Replace
pressure switch.
If this did not correct the problem, go to
step 8.
Yes. Correct water leak.
No. Go to step (2)
Yes. Correct the air leak problem.
No. Go to step (3-4)
Defective. Replace the pressure switch.
Good. Go to step (5)
If this did not correct the problem, go to
step 5.
No. Close the drawer.
Yes. Go to step (2).
Magnet missing or defective. Replace the
magnet.
Magnet good. Go to step (3).
Defective. Replace the reed switch.
Good. Replace the control board.
Restriction. Correct problem.
No restriction. Go to step (2).
Zero. Replace the control board.
120 VAC. Remove the pump and check
for
blockage. If blocked, remove the restriction,
if not, replace the pump.
Defective wiring. Correct wiring.
Good wiring. Replace the pressure sensor.
If this does not correct the problem, replace
the control board.
1. Is the incoming water flow normal?
2.
Are the incoming water faucets turned
3.
Is the incoming water pressure above (30) psi.
4.
Does the fill water continue enter the washer?
5.
Remove power from the washer. Did the water fill
stop?
6. Good models, check the pressure switch.
7. Better models, replace the pressure sensor.
8. Replace the control board.
1. Is the washer leaking water?
2. Is there an air leak in the air bell system?
3. Good models, check the pressure switch.
4. Better models, replace the pressure sensor.
5. Replace the control board.
1. Is the dispenser drawer closed?
2. Remove the drawer and check the magnet.
3. Open the console and check the reed switch.
1. Check the drain hose for restrictions.
2. Start the washer and check for 120 VAC at the
drain pump.
Inspect the wiring between the pressure sensor and
the control board.
P/N 134408500