Fujitsu MAF3364LC Manual/User Guide - Page 90

Each mode setting, power source TERMPOW.

Get Fujitsu MAF3364LC - Enterprise 36.4 GB Hard Drive PDF manuals and user guides View all Fujitsu MAF3364LC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Table 5.1 SCSI ID setting (CN2) SCSI ID CN2 7-8 5-6 3-4 0 Open Open Open 1 Open Open Open 2 Open Open Short 3 Open Open Short 4 Open Short Open 5 Open Short Open 6 Open Short Short 7 Open Short Short 8 Short Open Open 9 Short Open Open 10 Short Open Short 11 Short Open Short 12 Short Short Open 13 Short Short Open 14 Short Short Short 15 (*1) Short Short Short *1 Set at factory shipment 1-2 Open Short Open Short Open Short Open Short Open Short Open Short Open Short Open Short IMPORTANT 1. Set the SCSI ID so that there are no duplicates between SCSI devices on the same SCSI bus. 2. The priority of SCSI bus use in ARBITRATION phase is determined by SCSI ID as follows: 7 > 6 > 5 > 4 > 3 > 2 > 1 > 0 > 15 > 14 > 13 > 12 > 11 > 10 > 9 > 8 5.3.2 Each mode setting (1) Setting terminal power supply Refer to Table 5.2 for controlling the supply of power from the drive to the SCSI terminal resistance power source (TERMPOW). However, this setting may not be used with SCA2 type 16 bit-SCSI (LC/MC). For information on LP/MP, refer to Figures 5.2 and 5.3. Table 5.2 Setting SCSI terminal power supply (LP/MP) Supply on/off of SCSI terminating resistor power from IDD Supply off Supply on *1 Setting at factory shipment CN2 23-24 Open Short (*1) C141-E064-03EN 5 - 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
C141-E064-03EN
5 - 7
Table 5.1
SCSI ID setting (CN2)
SCSI ID
CN2
7-8
5-6
3-4
1-2
0
Open
Open
Open
Open
1
Open
Open
Open
Short
2
Open
Open
Short
Open
3
Open
Open
Short
Short
4
Open
Short
Open
Open
5
Open
Short
Open
Short
6
Open
Short
Short
Open
7
Open
Short
Short
Short
8
Short
Open
Open
Open
9
Short
Open
Open
Short
10
Short
Open
Short
Open
11
Short
Open
Short
Short
12
Short
Short
Open
Open
13
Short
Short
Open
Short
14
Short
Short
Short
Open
15 (*1)
Short
Short
Short
Short
*1
Set at factory shipment
IMPORTANT
1.
Set the SCSI ID so that there are no duplicates between SCSI devices
on the same SCSI bus.
2.
The priority of SCSI bus use in ARBITRATION phase is determined by
SCSI ID as follows:
7 > 6 > 5 > 4 > 3 > 2 > 1 > 0 > 15 > 14 > 13 > 12 > 11 > 10 > 9 > 8
5.3.2
Each mode setting
(1)
Setting terminal power supply
Refer to Table 5.2 for controlling the supply of power from the drive to the SCSI terminal resistance
power source (TERMPOW).
However, this setting may not be used with SCA2 type 16 bit-SCSI
(LC/MC).
For information on LP/MP, refer to Figures 5.2 and 5.3.
Table 5.2
Setting SCSI terminal power supply (LP/MP)
Supply on/off of SCSI terminating resistor power from IDD
CN2 23-24
Supply off
Open
Supply on
Short (*1)
*1
Setting at factory shipment