Fujitsu MAF3364LC Manual/User Guide - Page 93

Mounting Drives, 5.4.1 Check before mounting, 5.4.2 Mounting procedures, Indicated

Get Fujitsu MAF3364LC - Enterprise 36.4 GB Hard Drive PDF manuals and user guides View all Fujitsu MAF3364LC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

5.4 Mounting Drives 5.4.1 Check before mounting Reconfirm if the setting terminals are set correctly according to Table 5.8 before mounting the drive in the system cabinet. For setting terminals location, see Section 5.3. Setting terminal CN2 Table 5.8 Setting check list No. Setting contents (Check item) 1 SCSI ID 2 Write protect 3 Motor start mode 4 Force Narrow 5 Force single ended 6 Terminal power supply Setting position CN2 7 - 8 5 - 6 3 - 4 1 - 2 CN2 9 - 10 CN2 11 - 12 CN2 13 - 14 CN2 15 - 16 CN2 23 - 24 Check Remarks (SCSI ID = __) Upper bus (DB 8 to 15 PI) not connected Short Open Short Open Short Open Short Open Short Open LP/MP models 5.4.2 Mounting procedures Since mounting the drive depends on the system cabinet structure, determine the work procedures considering the requirements specific to each system. The general mounting method and items to be checked are shown below. See Subsection 4.2 for the details of requirements for installing the IDD. 1) With a system to which an external operator panel is mounted, if it is difficult to access the connector after the drive is mounted on the system cabinet, connect the external operator panel cable before mounting the drive. 2) Fix the drive in the system cabinet with four mounting screws as follows: • The drive has 10 mounting holes (both sides: 3 ×2, bottom: 4). Fix the drive by using four mounting holes of both sides or the bottom. (See Figure 4.9) • Use mounting screws whose lengths inside the drive mounting frame are 4 mm or less when the screws are tightened (see Figure 4.8). • When mounting the drive, be careful not to damage parts on the PCAs. 3) Check to ensure that the DE is not touching the frame on the system side after tightening the screws. At least 2.5mm of clearance is required between the DE and the frame. (Indicated in Figure 4.8) 4) When an electric driver is in use, less than low-impact device specifications must be used. 5 - 10 C141-E064-03EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
C141-E064-03EN
5 - 10
5.4
Mounting Drives
5.4.1
Check before mounting
Reconfirm if the setting terminals are set correctly according to Table 5.8 before mounting the
drive in the system cabinet.
For setting terminals location, see Section 5.3.
Table 5.8
Setting check list
No.
Setting contents
(Check item)
Setting
position
Check
Remarks
1
SCSI ID
CN2
7 - 8
5 - 6
3 - 4
1 - 2
(SCSI ID = __)
Upper bus
(DB 8 to 15
PI)
not connected
2
Write protect
CN2
9 - 10
Short
Open
3
Motor start mode
CN2
11 - 12
Short
Open
4
Force Narrow
CN2
13 - 14
Short
Open
5
Force single ended
CN2
15 - 16
Short
Open
6
Terminal power supply
CN2
23 - 24
Short
Open
LP/MP models
5.4.2
Mounting procedures
Since mounting the drive depends on the system cabinet structure, determine the work
procedures considering the requirements specific to each system.
The general mounting
method and items to be checked are shown below.
See Subsection 4.2 for the details of requirements for installing the IDD.
1)
With a system to which an external operator panel is mounted, if it is difficult to access the
connector after the drive is mounted on the system cabinet, connect the external operator
panel cable before mounting the drive.
2)
Fix the drive in the system cabinet with four mounting screws as follows:
•
The drive has 10 mounting holes (both sides:
3
×
2, bottom:
4).
Fix the drive by
using four mounting holes of both sides or the bottom. (See Figure 4.9)
•
Use mounting screws whose lengths inside the drive mounting frame are 4 mm or less
when the screws are tightened (see Figure 4.8).
•
When mounting the drive, be careful not to damage parts on the PCAs.
3)
Check to ensure that the DE is not touching the frame on the system side after tightening
the screws. At least 2.5mm of clearance is required between the DE and the frame.
(Indicated in Figure 4.8)
4)
When an electric driver is in use, less than low-impact device specifications must be used.
Setting
terminal
CN2