Garmin ColorMap Owners Manual - Page 80

Appendix E

Get Garmin ColorMap - StreetPilot ColorMap GPS Receiver PDF manuals and user guides
UPC - 753759016470
View all Garmin ColorMap manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Appendix E Messages The StreetPilot uses an on-screen message system to alert you to unit operating characteristics. Press the ENTER key to acknowledge and return to the page you were viewing. Battery Power is Low - The batteries in your unit are low and no longer capable of supporting unit operation. Install new batteries. Data Card Checksum Failure - There is an error in the unit's database. Service is required. Data Transfer Complete - The unit has finished uploading or downloading information to the connected device. Leaving Planned Route - You are no longer traveling along the planned route. Make corrections as necessary. Memory Battery Power is Low - The power that sustains user memory is low and should be replaced by an authorized service center as soon as possible No Differential GPS Position - The beacon receiver is not communicating with the unit. Go to the 'Interface' setup page to view status messages. No Matching Addresses Found - There is no such address in the map information database. Check spelling or number entry and try again. No Matching Intersections Found - There is no such intersection in the map information database. Check spelling and try again. Poor Satellite Reception - The unit cannot receive enough satellite signals to compute a position. Move to a location with a clearer view of the sky. Power Down and Re-init - The unit cannot calculate a position due to abnormal satellite conditions. Turn off and try again at a different location. RAM Failed - The unit has detected a failure in its internal memory. If the message persists, service is required. Receiver Has Failed - The unit has detected a failure. "Power Down and Re-Init: message will appear. If problem persists, service is required. Received Invalid Waypoint -A waypoint was received during upload transfer that has an invalid identifier. Degraded Accuracy - Accuracy has been degraded beyond 500 meters due to poor satellite geometry or data quality. Use other sources to verify position. Oscillator Needs Adjustment - The unit has detected excessive drift in its internal crystal oscillator. Take the unit to an authorized service center. ROM Failed - The permanent memory has failed and the unit is not operable. Service is required. Route Memory Full - No additional waypoints can be added. Route Waypoint Was Deleted - The waypoint being deleted was part of a route. The waypoint is removed from the route and waypoint memory. Speed Warning - Your current speed has exceeded the speed alarm setting. Stored Data Was Lost - All waypoints, routes, time, and almanac data have been lost due to battery failure, or the receiver's memory has been cleared. Too Many Turns - You have entered more turns in the route than the memory can hold. Restructure your route. Unknown Data Card Format - The unit does not recognize the format for the Map Data information you are downloading. Check data and settings. Using Sim for Faster Data Transfer - While using a MapSource program, simulator mode is automatically selected to speed data transfer. 70Waypoint Memory Full - All 500 personal waypoints have been assigned.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
70
Appendix E
Messages
The StreetPilot uses an on-screen message system to alert you to unit operating characteristics. Press
the
ENTER
key to acknowledge and return to the page you were viewing.
Battery Power is Low
- The batteries in your unit are low and no longer capable of supporting unit operation. Install new batteries.
Data Card Checksum Failure
- There is an error in the unit’s database. Service is required.
Data Transfer Complete
- The unit has finished uploading or downloading information to the connected device.
Leaving Planned Route
- You are no longer traveling along the planned route. Make corrections as necessary.
Memory Battery Power is Low
- The power that sustains user memory is low and should be replaced by an authorized service center as soon as possible
No Differential GPS Position
- The beacon receiver is not communicating with the unit. Go to the ‘Interface’ setup page to view status messages.
No Matching Addresses Found
- There is no such address in the map information database. Check spelling or number entry and try again.
No Matching Intersections Found
- There is no such intersection in the map information database. Check spelling and try again.
Poor Satellite Reception
- The unit cannot receive enough satellite signals to compute a position. Move to a location with a clearer view of the sky.
Power Down and Re-init
- The unit cannot calculate a position due to abnormal satellite conditions. Turn off and try again at a different location.
RAM Failed
- The unit has detected a failure in its internal memory. If the message persists, service is required.
Receiver Has Failed
- The unit has detected a failure.
“Power Down and Re-Init: message will appear. If problem persists, service is required.
Received Invalid Waypoint
-A waypoint was received during upload transfer that has an invalid identifier.
Degraded Accuracy
-
Accuracy has been degraded beyond 500 meters due to poor satellite geometry or data quality. Use other sources to verify position.
Oscillator Needs Adjustment
-
The unit has detected excessive drift in its internal crystal oscillator. Take the unit to an authorized service center.
ROM Failed
- The permanent memory has failed
and the unit is not operable. Service is required.
Route Memory Full
- No additional waypoints can be added.
Route Waypoint Was Deleted
- The waypoint being deleted was part of a route. The waypoint is removed from the route and waypoint memory.
Speed Warning
- Your current speed has exceeded the speed alarm setting.
Stored Data Was Lost
- All waypoints, routes, time, and almanac data have been lost due to battery failure, or the receiver’s memory has been cleared.
Too Many Turns
- You have entered more turns in the route than the memory can hold. Restructure your route.
Unknown Data Card Format
- The unit does not recognize the format for the Map Data information you are downloading. Check data and settings.
Using Sim for Faster Data Transfer
- While using a MapSource program, simulator mode is automatically selected to speed data transfer.
Waypoint Memory Full
- All 500 personal waypoints have been assigned.