Garmin GSD 20 Installation Guide - Page 6

Iring, Armin - wiring

Get Garmin GSD 20 - GPS Receiver Remote Sonar Sensor PDF manuals and user guides View all Garmin GSD 20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

INSTALLATION INSTRUCTIONS 4 GSD 20 Sonar Module BASIC WIRING FOR THE GARMIN GSD 20 TO A DUAL GPSMAP 2006/2006C/2010/2010C *This diagram does not apply to the GPSMAP 3005C/3006C/3010C. Refer to Note 4 on the Single GPSMAP 2006/2006C/2010/2010C/3005/C3006C/3010C diagram. ��� ���� ��� ��� ���� ���� ��� ���� BATTERY 10-35 VOLTS DC Notes: 1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs over 30' (9.1 m). 2. Refer to the GPSMAP 2006/2006C/2010/2010C Installation Instructions for wiring the GPS 17 sensor and other devices. 3. For runs over 30' (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the end of the shield drain wire. 4. Use unit #1 to update the GSD 20 software.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
4
GSD 20 Sonar Module
I
NSTALLATION
I
NSTRUCTIONS
�±²³
´µ¶µ²
·¶¸´¹
µ²¸º»³
²³¼
�½±¾³¿·¶À³
·¶¸´¹
²³¼
�½±¾³¿·¶À³
�½±¾³¿·²µ�º
�½±¾³¿·²µ�º
�½±¾³¿·¶¸´¹
�½±¾³¿²³¼
�±²³
´µ¶µ²
Á¸
ÃÀij
µ²¸º»³
ŸÂ
ÃÀij
»¸²Æ±ºÂ»Ä¼ÂÅÇ
ĵÀº¼³²ÂƵ¼À¶³
¾µÂ¾²¸ºÄ¼À´³²
�±²³
´µ¶µ²
·¶¸´¹
²³¼
�½±¾³¿·¶À³
�½±¾³¿·²µ�º
µ²¸º»³
Á¸
ÃÀij
�±²³´±µ¶··¸¹¶·º·
ȼ
�±²³´±µ¶··¸¹¶·º·
Ȧ
BATTERY
10-35 VOLTS DC
B
ASIC
W
IRING
FOR
THE
G
ARMIN
GSD 20
TO
A
D
UAL
GPSMAP 2006/2006C/2010/2010C
*This diagram does not apply to the GPSMAP 3005C/3006C/3010C. Refer to Note 4 on the Single GPSMAP
2006/2006C/2010/2010C/3005/C3006C/3010C diagram.
Notes:
1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs over 30’ (9.1 m).
2. Refer to the
GPSMAP 2006/2006C/2010/2010C Installation Instructions
for wiring the GPS 17 sensor and other devices.
3. For runs over 30’ (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the end of the shield drain wire.
4. Use unit #1 to update the GSD 20 software.